Assessments - 3, GPA: 4.3 ( )

Fabricante : Superior Arquivo Tamanho: 475.12 kb Arquivo Nome : Língua de Ensino:

These appliances may be used for bedroom installations in the United States and are listed accordingly. These units may not be installed in bedrooms in Canada. CLEARANCES Minimum clearance to combustibles for the appliance is as follows: sides and back - 0" (0 mm), floor - 0" (0 mm), adjacent wall - 0" (0 mm), ceiling - 64" (1626 mm). NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. APPLIANCE SPECIFICATIONS 4" (146 mm) 5 ..." (102 mm) 7 ..." (184 mm) 33 ..." (851 mm) 6" (152 mm) Front Appliance Top Spacer 33 ..." (851 mm) 32" (813 mm) Alternate Gas Junction Box Line Access 14" (356 mm) Left Side Right Side Appliance Top Spacer Top View Figure 2 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 38" (965 mm) 1" (25 mm) 36" (914 mm) 20 ..." (514 mm) 6 ..." (159 mm) 2" (51 mm) 5" (127 mm) 2 ..." (64 mm) Gas Line Access6 ..." (159 mm) Combustion Air Inlet 9 ..." (235 mm) 9 ...." (238 mm) 14" (356 mm) 2 ..." (64 mm) 28 ...." (716 mm) 14" (356 mm) 4 ..." (118 mm) 38" (965 mm) Venting Gas Vent Rule – Gas vent caps are not permitted within 8 feet (2.4 mm) of a vertical wall or similar obstruction. Gas vent caps that are located 8' or more from a portion of a building which extends at an angle greater than 45° upward from the horizontal may terminate in accordance with Table 1 (Figure 3), provided that in no case shall any discharge opening on the cap be less than 2' (610 mm) horizontally from the roof surface (National Fuel Gas Code ANSI Z223.1 (NFPA 54) 7.6.2) (CAN/CGA B149). Roof Pitch is X/12 12 X Minimum Height from Roofto Lowest Discharge Opening Figure 3 Roof Slope Minimum Height from Roof to Lowest Discharge Opening Feet Meters Flat to 6/12 1' 0" 0.3 Over 7/12 to 9/12 2' 0" 0.6 Over 10/12 to 12/12 4' 0" 1.2 Over 13/12 to 16/12 6' 0" 1.8 Over 17/12 to 21/12 8' 0" 2.4 Note: Venting terminals shall not be recessed into a wall or siding. Table 1 Multiple Terminations – These appliances may vent adjacent to and at the same level with any other gas appliances (including direct-vent appliances) provided that there is at least 2 ft. (0.6m) between the proximal edges of the vent caps. These appliances may be vented adjacent to a chimney vent servicing a solid fuel fireplace provided the B-vent cap is at least 2 ft. (0.6m) away from the nearest point of the chimney opening. FRAMING SPECIFICATIONS Header B AFireplace Framing Figure 4 Back Wall of Chase/EnclosureIncluding Finishing Materialsif any C G A RoughFraming FaceInside Chase (Unfinished Shown) Figure 5 Back Wall of Chase/Enclosure Including Finishing Materials if any C A Outside Chase Figure 6 G Rough Framing Face (Unfinished Shown) Back Wall of Chase/EnclosureIncluding Finishing Materialsif any H D C A E G F RoughFraming Face Corner Installation (Unfinished Shown) Figure 7 Framing Dimensions A 38 ..." 978 mm B 33 ..." 857 mm C 28 ...." 716 mm D 14" 356 mm E 55" 1397 mm F 27 ..." 699 mm G 13 ..." 343 mm H 38 ..." 987 mm Note:All framing dimensions calculated for 1/2" dry wall at the appliance face. If sheathing the chase or finishing with other thickness materials, calculations will need to be made. TYPICAL INSTALLATION SEQUENCE The typical sequence of installation follows, however, each installation is unique resulting in variations to those described. 1. Construct the appliance framing. 2. Route gas supply line to appliance location. 3. Install nailing flanges and position the appliance. 4. Install the vent system and exterior termination. 5. Field wire and install operating control switch. 6. Make connection to gas supply. 7.Install (optional) outside Air Kit. 8. Check log position. 9. Checkout appliance operation. 10. Adjust burner to ensure proper flame appearance. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. PRE-INSTALLATION NOTES The fireplace may be installed directly on a combustible floor or raised on a platform of an appropriate height. Do not place fireplace on carpeting, vinyl or other soft floor coverings. It may, however, be placed on flat wood, plywood, particle board or other hard surfaces. Be sure fireplace rests on a solid continuous floor or platform with appropriate framing for support and so that no cold air can enter the room from under the fireplace. The fireplace may be positioned and then the framing built around it, or the framing may be constructed and the fireplace positioned into the opening. Usually, no special floor support is needed for the fireplace, however, to be certain: 1. Estimate the total weight of the fireplace system and surround materials such as brick, stone, etc., to be installed. 2. Measure the square footage of the floor space to be occupied by the system, surrounds and hearth extensions. 3. Note the floor construction, i.e. 2 x 6’s, 2 x 8’s or 2 x 10’s, single or double joists, type and thickness of floor boards. 4. Use this information and consult your local building code to determine if you need additional support. If you plan to raise the fireplace and hearth extension, build the platform assembly then position fireplace...

Baixe o seu

Para fazer o download, introduza 2 dígitos :