Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
56 ... 97 ... 103 104 ... 106 ... 1 1 1 1 0 0 0 0 1 0 1 2 1 2 0 1 2 2 0 2 0 0 2 0 58 ... 61 ... 64 ... 67 109 ... 116 121 ... 124 ... 1 1 1 1 0 1 1 1 0 1 0 2 1 0 1 0 0 3 3 3 2 0 0 0 68 ... 70 73 74 ... 128 130 135 ... 138 ... 1 1 1 1 1 1 1 1 0 1 0 0 0 1 2 0 1 3 3 0 2 0 0 3 79 80 82 82 ... 145 ... 147 ... 150 ... 152 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 4 0 4 0 0 3 0 3 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Stabilizer A1 20' Max. B1 10' Max. Offset Elbow Figure 37 A1 C1 B1 B2 C2 A2 A1 C1 B1 B2 C2 A2 Figure 38 ChimneySection Joints No. 8 x 1/2" SMS Screws Required AtEvery Joint Past 6' No Screws Required InJoints For First 6' of Offset 4' 6' Underside Of Chimney Figure 38 ChimneySection Joints No. 8 x 1/2" SMS Screws Required AtEvery Joint Past 6' No Screws Required InJoints For First 6' of Offset 4' 6' Underside Of Chimney Figure 39 FTF8-E30 Return Elbow* Chimney Section (S) FTF8-30 Offset Elbow* B A *Part of Offset/Return Package Model FTF8-ES30 Figure 40 INSTALLING OFFSETS First, review the Offset Elevation Chart and Figure 40 for reference. Step 1. Determine the offset distance where chimney is to pass through the first ceiling- dimension “A.” To find this point on your ceiling, first determine the center point for a vertical chimney following the instructions for vertical installation. Measure height to the ceiling from the top of fireplace-dimension “B.” Use the appropriate Offset Elevation Chart to find dimension “A.” Mark point where you will drive your nail to show the center point for your offset ceiling cut. Step 2. Proceed by using the Straight Up Installation Instructions for cutting and framing ceiling and roof openings. Note:See Framing and Dimension Chart for the sizes of the ceiling and roof openings. The size of the roof opening varies with the degree of pitch of the roof. Offset Elbow Assembly Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check connection by pulling up slightly to ensure a tight fit. Next, the outer sections snap lock OVER the preceding outer section of chimney. Again, check outer section by pulling up slightly to ensure proper connection is made. Return Elbow Assembly Return elbows install the same way as round terminations and stabilizers: Step 1. Hold return elbow over top of last chimney section. Step 2. Center inner slip section into inner flue pipe-slip down. Step 3. Center outer-locking section over outer chimney pipe. Push down until locking joint has firmly engaged. Step 4. Pull up slightly on return elbow to ensure locking joint has firmly engaged. Step 5. Secure support straps to framing members by nailing under tension in sheer (Figure 41). Note:The return elbow assembly performs the same function as a stabilizer. Consider this when determining the need for a stabilizer. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Return Elbow Figure 41 Note:The return elbow assembly performs the same function as a stabilizer. Consider this when determining the need for a stabilizer. Note:Do not apply excessive pressure to any subsequent chimney section following return elbow assembly when installing. Ensure that each subsequent chimney section is securely attached by testing as noted above. OPTIONAL EQUIPMENT CONSIDERATIONS Blower Kits (Circulating Models Only) Blower Kits model FBK-100/200 are available for use with circulating models. The Blower Kit can be installed prior to or after installation of the fireplace. When installing the FBK-100 Blower Kit, a Blower Switch Kit (Model FUBSK) is required. This switch kit allows for a unit mounted blower switch to be used. The FUBSK is not included and must be purchased separately. The FBK-200 Blower Kit comes standard with a wall mounted variable speed control switch. Note: The fireplace must have provisions for a wall mounted On/Off switch in order to install the FBK-200. THE FIREPLACE MUST BE WIRED TO THE HOUSE ELECTRICAL SYSTEM AT THE TIME OF INSTALLATION IN ORDER FOR THE OPTIONAL FANS TO OPERATE, (SEE FIGURES 42 AND 43). Note: The utilization of fans will increase the air flow around the firebox. However, only a minimal increase in heat output should be anticipated. THIS FIREPLACE IS NOT INTENDED TO BE USED AS A SUBSTITUTE FOR A FURNACE TO HEAT AN ENTIRE HOME. USE FOR SUPPLEMENTARY HEATING ONLY. POWER TO THE FIREPLACE POWER TO THE FIREPLACE COVER PLATE Replace Cover Plate After Electrical Hook-Up House Wiring Must Be SecuredWith The Appropriate Electrical Connector To The Fireplace Convenience Outlet Wiring Figure 42 BLOWER THREE PRONGED PLUG TO GROUNDED OUTLET Figure 43 The FBK-100/200 Blower Kits are design certified by Warnock Hersey for use with these appliances. Always check local building codes. Installation of the FBK Blower Kits must comply with local regulations as well as the National Electric Code. Combustion Air Kits These appliances are equipped with an outside (make-up) air door and integral actuator arm. If the appliance is to be i...
Este manual também é adequado para os modelos :Lareiras - BC-36 (305.34 kb)
Lareiras - BC-36-2 (305.34 kb)
Lareiras - BCI-36 (305.34 kb)
Lareiras - br-36 (305.34 kb)