Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Please read the instructions carefully in order to enjoy your product fully. GENERAL INSTRUCTIONS Remove the fire from the packaging, checking that neither the fire nor the power cable has been damaged during transport. Do not operate the fire if damaged. The pebbles can be found in one of the two long brown boxes that fit down either side of the fire, so ensure that the accessories are removed before discarding the boxes. INSTALLATION OF THE FIRE Your fire is designed for use against a flat wall surface, and a spacer frame is supplied to enable it to fit flush. Alternatively you can use within an existing chimney or as part of a fireplace mantel and surround suite. The rebate depth is standard at 23/ 4 inches (7cm) which should fit perfectly. Position the fire so that the plug socket is accessible. IMPORTANT: Access must be allowed for the fire to be serviced, which involves the heater being moved forward in order to accessthe rear. Sufficient mains lead must be available to allow the fire to be moved for access when servicing. Should you wish to connect the fire to a fused spur, this must be carried out by a competent electrician in accordance with the IEE wiring regulations. Where the inset fire is being used in an existing chimney, it is important that the chimney is blocked off to prevent airflow problems within the fire. Where a chimney is not blocked off sufficiently the heater may cut out and the flame effect stop, or work poorly. ELECTRICAL CONNECTION ( UK Only) Your appliance comes fitted with a plug and will incorporate a 13 amp fuse. If it does not fit your socket, the plug should be cut off from the mains lead and an appropriate one fitted as below. WARNING: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse the circuit must be protected by a 15 amp fuse. If the plug is a moulded-on type, the fuse cover must be refitted when changing the fuse using a 13amp Astra approved fuse to BS1362. In the event of losing the fuse cover, the plug must not be used until a replacement fuse cover can be obtained from your nearest electrical dealer. The colour of the correct replacement fuse cover is that marked on the base of the plug. WARNING- THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code; Green and yellow: EARTH Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The green and yellow wire must be connected to the terminal in the plug marked with the letter E or the earth symbol or coloured green or green and yellow. The blue wire must be connected to the terminal marked with the letter N or coloured black. The brown wire must be connected to the terminal marked with the letter L or coloured red. OPERATING THE FIRE Controls The on/off push button switch is located on the top right hand side of the fire. Pushed in, it will illuminate the fire with no heat, so that you may enjoy the flame effect all year round. Pushed again the switch will return to its outer position and turn the fire off. To use the heating element (the heater element is under the hood), press the button marked with one red bar. The fire is 2kW and is thermostatically controlled. The thermostat is positioned nest to the heat switch. We suggest that you turn the thermostat up to the maximum. Then, once the required room temperature is achieved, turn the thermostat towards minimum until you hear a click and the heater turns off. The thermostat will then regulate the room temperature automatically. Please note that there can be several 0C drop or rise in temperature to activate or deactivate the thermostat. The temperature is taken from near tothe fire and therefore some fluctuations may arise. Other situations such asthe size of the room, the airflow within the room, and the proximity to otherheat sources may cause fluctuations in the thermostat’s efficiency. Automatic Safety Cut Out This heater is fitted with an automatic cut out to prevent any damage due to overheating. The heater will automatically cut out if the airflow is obstructed. To reset the fire, switch off the fire, remove the cause of overheating and allow a suitable cooling period then switch the fire back on. Noise As with all fan driven appliances the fire will make some noise due to the movements of air occurring, this is perfectly normal. MAINTENANCE Before any maintenance / cleaning is undertaken always disconnectthe fire from the power supply. Replacing light bulbs Your fire comes fitted with two 60W clear bayonet cap bulbs. Replacements are available from good hardware/large DIY stores. Allow a suitable time for the bulbs to cool and remove all the pebbles. Then unscrew the knob at the base of the fire and remove the fret a...