Assessments - 1, GPA: 3 ( )

Fabricante : Empire Comfort Systems Arquivo Tamanho: 3.9 mb Arquivo Nome : 914b4c70-2a27-45bc-a695-51ca3811cf01.pdf Língua de Ensino:

From 0 to a maximum of 8 ft. a vent pipe can be used between elbows. c) Wall straps must be used to support offset pipe every 4'. This application will require that you first determine the roof pitch and use the appropriate venting components. Figure 50 Page 32 23552-1-0607 23552-1-0607 Page 33 Before you begin: if you are installing logs into the DVD32 or DVD36 model then this fireplace is supplied with a set of five ceramic fiber logs. Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fibers. The positioning of the logs is critical to the safe and clean operation of this fireplace. Sooting and other problems may result if the logs are not properly and firmly positioned in the fireplace. Please refer to Figure 51 and Figure 52 and corresponding WARNING when completing following log placement instructions. 1. Remove top louver, grasp louver, lift and pull forward. 2. Lower bottom louver, lift and hinge forward. 3. Release two glass frame spring clamps at bottom of firebox. 4. Remove glass frame assembly. 5. Place front logs (#1 and #2) between front grate flange and main burner. Align notches on front logs with locator tabs in base. 6. Place middle log (#3) between front and rear loop of burner. Note: Do not place log on top of pilot assembly. 7. Place rear log (#4) on rear log shelf. Bottom flange of log must be placed between the log shelf and burner tube. 8. Place branch (#5) onto (#1) log and flat area on (#3) log. The bottom of the branch is to be placed behind the grate tang that is second from the left. 9. Place decorative rock in front of grates and sides of main burner pan. ATTENTION: Do not place decorative rock on logs or burner. The decorative rock should only be placed on the fireplace floor. EMBER MATERIAL PLACEMENT ON BURNER 10. After all logs are positioned properly, apply Rockwool ember material to the front burner port area. To apply, carefully separate the ember material into small amounts no larger than "dime size" pieces. Fluffed up pieces one layer thick on top of the burner generally works best, and will provide the best ember glow. Do not place ember material more than one layer thick. No more than (1) small packet of ember material (part no. 15999) evenly placed on the burner, is recommended on DVD32 and DVD36 models. Using additional ember material will decrease the amount of ember glow effect. Extra ember material should be saved for future ember applications as necessary. See Figure 51. 11. Replace glass frame onto firebox. 12. Secure the two glass frame spring clamps at bottom of firebox. 13. Align the tabs on top louver brackets with slots in front posts to secure top louver. 14. Close bottom louver. Lift slightly to engage the end tabs into the slots in fireplace sides to close louver panel Figure 51 WARNING: Failure to position the parts in accordance with this diagram or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. Attention: Do not use Figure 51 or Figure 52 to order logs. Refer to parts list on page 45 and parts view on page 46 to order logs and/or ember material for your appropriate fireplace model. Figure 52 1 2 3 5 4 EMBER MATERIAL PLACEMENT 1 4 5 3 2 LOG PLACEMENT (5 LOG SET) Page 34 23552-1-0607 Figure 53 Warning: Failure to position the parts in accordance with this diagram or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. Attention: Do not use Figure 53 or Figure 54 to order logs. Refer to parts list on page 45 and parts view on page 46 to order logs and/or ember material for your appropriate fireplace model. Before you begin: If you are installing logs into the DVD42 or DVD48 model then this fireplace is supplied with a set of seven ceramic fiber logs. Do not handle these logs with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fiber. The positioning of logs is critical to safe and clean operation of this fireplace. Sooting and other problems may result if the logs are not properly and firmly positioned in the fireplace. Please refer to Figure 53 and Figure 54 and corresponding WARNING when completing following log placement steps. 1. Remove top louver, grasp louver, lift and pull forward. 2. Lower bottom louver, lift and hinge forward. 3. Release two glass frame spring clamps at bottom of firebox 4. Remove glass frame spring assembly. 5. Place front logs (#1, #2, and #3) between grates and main burner. Align notches on front logs with locator tabs in base. 6. Place middle log (#4) between front and rear loop of burner. Note: do not place on top of pilot assembly. 7. Place rear log (#5) on rear log shelf. Bottom flange is to be placed between the log s...

Baixe o seu

Para fazer o download, introduza 2 dígitos :