Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
The permanent metal warning plate provided must be attached to the back of the fireplace stating the fire place may have been altered to accommodate the insert and must be returned to original condition for use as a conventional fireplace. September 1, 2008 250-7201E Page 5 RR 4100-I ACT WOOD INSERT LISTINGS These installation instructions describe the installation and operation of the Quadra-Fire 4100-I Wood Insert. This insert meets the U.S. Environmental Protection Agency’s 1990 particulate emission standards. This product is listed by OMNI-Test Laboratories, Inc. to UL Safety Standard 1482, and ULC S628, and (UM) 84-HUD. This insert is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided. The structural integrity of the mobile home floor, ceiling, and walls must be maintained. The insert must be properly grounded to the frame of the mobile home. CHIMNEY HEIGHT/DRAFT (CONT’D) AVOID FIRE: To ensure that insulation or any other com bustible material does not contact the chimney, a chimney inside the house must have at least 2 inches (51mm) of air space clearance around the chimney. A chimney outside the house must have at least one inch (25mm) clearance to the combustible structure. Noncombustible fire stops must be installed at the spaces where the chimney passes through floors and/or ceilings. Refer to Figures 8A & 8B on page 8. Canadian installations require a full reline of the chimney Check with your local building code agency before you begin your installation to ensure compliance with local codes, including the need for permits and follow-up inspections. Be sure local building codes do not supersede UL specifica tions and always obtain a building permit so that insurance protection benefits cannot be unexpectedly cancelled. If any assistance is required during installation, please contact your local dealer. CHIMNEY HEIGHT/DRAFT To be sure that your Quadra-Fire insert burns properly, the chimney draft (static pressure) should be approximately -0.10” water column (W.C.) during a high burn and -0.04” W.C. during a low burn, measured six inches (152mm) above the top of the insert after one hour of operation at each burn setting. NOTE: These are guidelines only, and may vary somewhat for individual installations. The insert was designed for and tested on a six inch (152mm) chimney, 12 ft-14 ft ( 60-420cm) high, measured from the base of the insert. The further your stack height or diameter varies from this configuration, the possibility of performance problems increases. In addition, exterior conditions such as roof line, surrounding trees, prevailing winds and nearby hills can influence insert’s performance. A masonry chimney or a listed factory-built UL10 HT Class “A” chimney must be the required height above the roof and any other nearby obstructions. The chimney must be at least ft (91cm) higher than the highest point where it passes through the roof and at least 2 ft (61cm) higher than the highest part of the roof or structure that is within 10 ft ( 05cm) of the chimney, measured horizontally. See 2-10-3 Rule (Figure 6A). These are safety requirements and are not meant to assure proper flue draft. ft Min (91cm) 2 ft Min (61cm) 10 ft Min ( 05cm) 2-10-3 RULE Figure 6A NOTE: Clearances may only be reduced by means approved by the regulatory authority having jurisdiction. WE RECOMMEND that a qualified building inspector and your insurance company representative review your plans before and after installation. INSTALLATION RECOMMENDATIONS This product has met and surpassed the most stringent emissions standards in the United States. The sophistication of the interior firebox design requires that a proper draft be supplied by the chim ney, therefore adherence to the following factors will enable your insert to operate at its optimum capability. REqUIRED: A minimum NFPA 211 required stainless steel liner connector pipe extending to the first flue liner of the existing code approved masonry chimney. To eliminate dilu tion air in the chimney, seal the damper area of the chimney around the chimney connector. BEST: A complete relining of the chimney system with a six inch (152mm) diameter listed, stainless steel liner. The liner must be connected to the insert flue collar and extend the entire height of the chimney, terminating slightly above a plate that seals the top of the chimney. All joints should be secured with sheet metal screws. The sections must be attached to the insert and to each other with the crimped (male) end pointing toward the insert. Figure 6B. Minimum clearances to combustibles must be maintained. A full reline is required for factory-built fireplace installations in Canada and is highly recommended in USA. LINER CONNECTOR CRIMPED END FLUETOWARDS GAS DIRECTIONSTOVE Figure 6B Page 6250-7201E September 1, 2008 4100-I ACT WOOD INSERT R GENERAL INSTALLATION pROCEDURE • DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVIN...
Este manual também é adequado para os modelos :Lareiras - 4100I-NL-B (3.9 mb)