They should sit on the bottom row of small coals or pebbles and rest against the inner mass of square blocks. Place one small coal or pebble on top of the centre of the square blocks. See diagram 16. 16 AR1272 18 INSTALLATION INSTRUCTIONS INSTALLATION 5.6.4 Place the remaining 4 large coals or pebbles on top of the square blocks, ensure that they lean against the central small coal or pebble and that there are gaps between each coal or pebble. See diagram 17. AR1273 17 5.7 Log & Driftwood Layout – Small Aspen & Chamonix It may be necessary to make small changes to the log positioning in order to achieve the most pleasing flame effect but the following guidelines should be followed. 5.7.1 Refer to the log identification chart and identify the numbers corresponding to the logs that have been supplied. See diagram 18 5.7.3 Place the large log (No. 1) so that it sits on top of the previous two logs. Place the burnt effect log (No. B1) in the centre of the tray as shown. See diagram 20. 20 AR1275 5.7.4 Place log (No. 7) along the LH side of the tray, log (No. 9) along the RH side of the tray and place logs (No. 8 and 11) along the front of the tray as shown. Place the cone (No. 14) on the LH side of the burnt log. See diagram 21. 21 AR1276 5.7.5 Place the large log (No. 6) so that it rests on top of the rear and front logs to the LH side, Place log (No. 7) on the RH side and log (No. 8) so that it bridges the centre gap as shown. See diagram 22. 18 8 5.7.2 Place the two logs (No.13) on top of the beads as shown. See diagram 19. 19 AR1274 22 AR1277 19 INSTALLATION INSTRUCTIONS INSTALLATION 5.8 Log & Driftwood Layout – Medium Chamonix, Large Aspen & Chamonix It may be necessary to make small changes to the log positioning in order to achieve the most pleasing flame effect but the following guidelines should be followed. 5.8.1 Refer to the log identification chart and identify the numbers corresponding to the logs that have been supplied. See diagram 23. 5.8.3 Place the large log (No. 1) so that it sits on top of the previous two logs. Place the burnt effect log (No. A1) in the centre of the tray as shown. Place one log (No. 7) along each side of the tray, another log (No. 7) along the front LH side and a log (No. 8) along the front RH side of the tray. See diagram 25. 23 8 5.8.2 Place the two logs (No.13) on top of the beads as shown. See diagram 24. 25 AR1279 5.8.4 Place two cones (No. 14), one in the RH front corner and the other at the LH side of the burnt log. See diagram 26. 26 AR1280 24 AR1278 5.8.5 Place one large log (No. 6) so that it rests on top of the rear and front logs to the LH side. Place the other large log (No. 6) so that it rests on top of the rear and front logs on the RH side and log (No. 8) so that it bridges the centre gap as shown. See diagram 27. 27 AR1281 20 INSTALLATION INSTRUCTIONS INSTALLATION 5.9 Log & Driftwood Layout – Tahoe 5.9.4 Place one log (No. 8) in the centre so that it rests on the rear cone and the pilot shield. See diagram 31. It may be necessary to make small changes to the log positioning in order to achieve the most pleasing flame effect but the following guidelines should be followed. 5.9.1 Refer to the log identification chart and identify the numbers corresponding to the logs that have been supplied. See diagram 28. 31 AR1284 5.9.5 Place one log (No. 11) so that it rests on the LH front log and the burnt log. Place another log (No. 7) so that it rests on the RH front log and the burnt log. See diagram 32. 28 8 5.9.2 Place a cone (No. 14) in the centre at the rear edge of the tray and place one log (No. 13) at each side of the cone. Place one log (No. 11) along the front of the tray at each side of the pilot. See diagram 29. 5.9.3 Place the burnt effect log (No. B1) in the centre of the tray. See diagram 30. 29 AR1282 32 AR1285 5.9.6 Place the two thin logs (No. 12), one at each side sitting on the tray and resting against the previously positioned logs. Place one log (No. 9) at the LH rear resting on the base log, and one log (No. 8) at the RH rear. See diagram 32. 33 AR1286 30 AR1283 21 INSTALLATION INSTRUCTIONS COMMISSIONING 6. COMMISSIONING 6.1 Close all windows and doors to the room, check all controls, and allow fire to burn on maximum for 5 minutes. Test for spillage of flue products using a smoke match. Pass the lighted smoke match along the top front edge just inside the opening or canopy. See diagram 34. 34 6.2 If the fire spills, run for a further 10 minutes and re-check. If there is still spillage, disconnect the fire and seek expert advice 6.3 If there are extractor fans in the room or adjacent rooms, the spillage test must be repeated with the extractors running on maximum. 6.4 The burner pressure on this appliance is pre-set, provided the correct inlet pressure is obtained at the test point on the inlet connection, with the appliance on full, the appliance will work correctly. Carrying out a gas rate test will check the correct operation. ( The test poi...

Este manual também é adequado para os modelos :
Lareiras - Chamonix & Aspen (P)8120**UC (602.53 kb)
Lareiras - Chamonix & Aspen (P)8127**UC (602.53 kb)
Lareiras - Chamonix & Aspen (P)8128**UC (602.53 kb)
Lareiras - Chamonix & Aspen (P)8135**UC (602.53 kb)