Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
(For details on the MPX filter, see “Glossary” on page 17.) 5 Basic Operations Basic Operations Playing a Tape 23 POWER OFFREC PLAY TIMER REC LEVEL DOLBY NR OFF B C S • • • • REC EQ BIAS REC LEVELMONITOR PHONES LEVEL .AMS ± 0() § rRPpPAUSE REC MUTE REC OPEN/CLOSE RESET MPX FILTER HX PRO CALIBRATION MEMORY 4 See page 7 for hookup information. To play a tape recorded with the Dolby NR system Set DOLBY NR to the same position that the tape was recorded in—B, C, or S. You can connect the headphones to PHONES To adjust the volume, turn PHONES LEVEL. 1 1 Turn on the amplifier and select the tape deck position. 2 2 Set TIMER to OFF and press POWER. 3 3 Press § OPEN/CLOSE and insert a cassette. With the side you want to play facing you 4 4 Press (. The cassette holder closes and the deck starts playing. “TAPE” and the tape type (I, II, or IV) appear in the display. Adjust the volume on the amplifier. To Press Stop playing p Pause P PAUSE. Press the button again to resume play. Fast-forward or rewind ) or 0 when the deck is stopped Take out the cassette § OPEN/CLOSE after stopping playing Getting Started Getting Started Unpacking Check that you have received the following supplied items: • Remote commander (remote) RM-J701 (1)* • Size AA (R6) batteries (2)* • Audio connecting cord (2) * Canadian model only Inserting batteries into the remote (Canadian model only) Insert two size AA (R6) batteries, matching the + and – on the batteries with the markings inside the battery compartment. When using the remote, point it at the remote control sensor g on the tape deck. When to replace batteries With normal use, the batteries should last for about 6 months. When the remote no longer operates the tape deck, replace all the batteries. Notes • Do not leave the remote near an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or lighting equipment. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Hooking Up the System This section describes how to hook up the tape deck to an amplifier. Be sure to turn off the power of each component before making the connections. TC-KA6ES/KA3ES to LINE IN to LINE OUT / to an AC outlet (or a switched outlet on the amplifier when using a timer) to REC OUT to TAPE IN Amplifier / to a wall outlet Hookups When connecting an audio cord, be sure to match the color-coded cord to the appropriate jacks on the components: Red (right) to Red and White (left) to White. Be sure to make connections firmly to avoid hum and noise. Connect the tape deck to the amplifier as shown below. Tape deck Amplifier C LINE IN OUT L L R R TAPE REC OUT IN L L R R c (Continued) Basic 7 Getting Started LINE IN OUT L L R R To connect your tape deck to another tape deck Connect both tape decks as shown below. Tape deck Another tape deck LINE IN OUT L L R R c C Setting the voltage selector (only on models supplied with a voltage selector) Check that the voltage selector on the rear panel of the tape deck is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to an AC outlet. 220V 240V 120V VOLTAGE Connecting the AC power cord Connect the AC power cord to an AC outlet. The tape deck’s Memory Backup function (page 17) keeps the various settings in memory even after you turn off the power as long as AC power cord is plugged in. Where do I go next? Now you’re ready to use your tape deck. For basic operations, go to pages 4 to 6; for advanced operations, go to the sections immediately after this one. Advanced Playback Operations Advanced Playback Operations Locating a Track (AMS/Auto Play/ Memory Play) You can locate the following/previous tracks (AMS: Automatic Music Sensor) or the beginning of a tape quickly. You can even locate a specific point anywhere on a tape. .± RESET MEMORY(0POWER OFFREC PLAY TIMER REC LEVEL –3 0 +3 •• • • • •• • • • • DOLBY NR OFF B C S • • • • REC EQ –2 0 +2 •• • • • •• • • • • BIAS REC LEVEL 5 4 3 2 1 0 6 7 8 9 10 RL MONITOR –20 0 +20 •• • • • •• • • • • PHONES 0 LEVEL 10•• .AMS ± 0() § rRPpPAUSE REC MUTE REC OPEN/CLOSE RESET MPX FILTER HX PRO CALIBRATION MEMORY MEMORY To locate Press the beginning of the next or succeeding tracks (AMS*) ± as many times as you want while playing. For example, to locate 2 tracks ahead, press twice. the beginning of the current track (AMS*) . once while playing the beginning of the preceding tracks (AMS*) . as many times as you want while playing. For example, to locate 2 tracks behind, press three times. the beginning of a tape (auto play) a particular point on a tape (memory play) MEMORY repeatedly until “MEMORY” disappears in the display. Then press 0 while holding down (. MEMORY repeatedly until “MEMORY” appears in the displa...
Este manual também é adequado para os modelos :decks de cassetes - TC-KA3ES (262.49 kb)