Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Failure to do so will result in movement of the brewer which can cause personal Injury and/ or damage to brewer. WARNING ELECTRIC SHOCK HAZARD: Brewer must be plugged into a properly grounded electrical receptacle to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket (#33) and Spray Disk (#34) are properly installed. LEVELING THE UNIT Verify that an adjustable leg is installed at each corner of the brewer. Set Brewer in its operating location. Level the Brewer. A spirit level should be placed on the top of the unit, at the edge, as a guide when making level adjustments. Level the unit from left to right and front to back by turning the adjustable feet. Be sure all four feet touch the counter to prevent tipping. FILL WATER TANK Check the bottle ring for lint or packing materials. Wipe the interior of the bottle ring with a cloth dampened with clean water. Brewer is designed to use a 3 gallon or 5 gallon plastic water bottle. Carefully insert a fresh water bottle into the bottle ring. Wait 30 seconds, or until all bubbling in the bottle stops, then drain water from the hot water faucet until all air is purged from the tank. ELECTRICIAN’S INSTALLATION INSTRUCTIONS REFER TO ELECTRICAL SPECIFICATIONS -Page 1 Check the nameplate to determine correct electrical service required for the Brewer to be installed. IMPORTANT: Before connecting to electricity, make sure a bottle of water is installed on the bottle ring, and all air has been bled from the water tank Model 8372 is equipped with a cord and plug. It requires a 115 - 125 volt 20 amp circuit (50/60 Hz, 2 wire plus ground, with NEMA 5-15R or 5-20R Receptacle). IMPORTANT: Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the brewer or result in decreased performance. Such damage is not covered by warranty. IMPORTANT: The ground prong of the plug is part of a system designed to protect you from electrical shock in the event of internal damage. Never cut off the ground prong nor twist a blade to fit an existing receptacle. Contact a licensed electrician to install the proper circuit and receptacle. 4 OPERATION 5 CAUTION: Personal Injury 5 Gallon water bottle can weigh up to 50 pounds. Install bottle carefully. Injury can result from improper lifting technique or from attempting to lift a full bottle without adequate physical ability. CAUTION: Equipment Electrical Damage DO NOT manually fill brewer through bottle ring. IMPORTANT: Use only 3 gallon or 5 gallon plastic water bottle. IMPORTANT: Tank must be full of water before connecting brewer to electrical power. Heating elements will be damaged if allowed to operate without being fully submerged in water. Damage caused by operating the brewer without water in the tank is NOT COVERED BY WARRANTY. IMPORTANT: This appliance is NOT designed to be used as a pour-over brewer. Operation without a water bottle with an adequate amount of water in place will produce very little or no brewed coffee. IMPORTANT: When installing water bottle, be careful to not overflow the basin pan. DO NOT fill the basin pan prior to installing the water bottle. START-UP For initial start-up, or if the brewer has not been used for an extended period of time: ¦ Be sure spray disk and brew gasket are properly installed in the brew head. ¦ Install a fresh bottle of water in the bottle ring. ¦ Allow basin and tank to fill. ¦ Plug unit into a properly grounded electrical receptacle. ¦ Draw water from the hot water faucet until all air is purged from the tank. NOTE: This brewer will not function as a “pour-over” brewer. A water bottle with an adequate amount of water must be installed for the brewer to operate. Once plugged into electrical power, the heating elements will begin heating the water in the tank. When the water has reached the proper temperature, the “READY TO BREW” light will glow. Fig 2. Brewer Operation Diagram OPERATION 5 CAUTION: Personal Injury 5 Gallon water bottle can weigh up to 50 pounds. Install bottle carefully. Injury can result from improper lifting technique or from attempting to lift a full bottle without adequate physical ability. CAUTION: Equipment Electrical Damage DO NOT manually fill brewer through bottle ring. IMPORTANT: Use only 3 gallon or 5 gallon plastic water bottle. IMPORTANT: Tank must be full of water before connecting brewer to electrical power. Heating elements will be damaged if allowed to operate without being fully submerged in water. Damage caused by operating the brewer without water in the tank is NOT COVERED BY WARRANTY. IMPORTANT: This appliance is NOT designed to be used as a pour-over brewer. Operation without a water bottle with an adequate amount of water in place will produce very lit...