Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
-Packing materials and consumed products shall be left/discarded at a municipal site. -Check the label and type designation to ensure that the voltage and frequency correspond to the mains. -Make sure that the switch is switched off before the machine is plugged in to the mains. -Damage to the mains flex increases the risk for electric shock and fire. Therefore, always pull the plug out from the socket by means of the actual plug- not by the flex or the machine. Never lift the machine by the flex. The flex shall never be drawn over sharp edges, or be exposed to heat or chemicals. Check that the flex is free from defects. If a fault is discovered, an authorized technician shall always replace a damaged or defective flex. -Never connect the machine to a defective wall socket. The risk for electric shock and short-circuiting increases. -A qualified technician must do any work carried out. - - - - - - - - - - - soap solution when cleaning. The machine must never be submerged in water or other liquid, neither during cleaning or operation. Do not allow children to use the machine unless under the supervision of an adult. Warning for heat and hot surface. Warning for hot steam! Make sure that the machine stands firmly on a stable surface. Make sure that defective parts are repaired, and that the machine’s operating reliability is maintained, before it is used. Use only original spare parts. Must not be started without water. To be used indoor only. Never fill more water into the pot than indicated on the inside of the pot. If the percolator is overfilled, boiling water may be ejected, causing a scalding hazard. Do not touch hot surface; percolator body, lid or lid knob. Use the handle. Before brewing and serving check that the lid is on. Never remove the lid during brewing. Do not touch hot surfaces; always use the handles and knobs provided. 10 LIST OF COMPONENTS 1. Lid knob (transparent) 2. Percolator lid 3. Basket lid 4. Handle 5. Water level indicator 6. Ready light 7. Power connection Percolator 8. Power cord 9. Power connection base 123567 8910111213 14 4 10. Power base 11. Heating element 12. Percolator tube 13. Spring 14. Coffee basket BEFORE BREWING FOR THE FIRST TIME -Wash and rinse the coffee percolator with hot water before using it for the first time. Also rinse the coffee container where the ground coffee is to be placed, the pipe and the lid. -You can also fill the coffee percolator with water up to the max. line. Leave the various parts in place and boil until the light comes on. Then pour out the water. USE -Fill the coffee percolator with the desired amount of cold water, do not fill higher that the marking "6" (for the 0,9 l model) or "12" (for the 1,3 l model). -When the water reached over the top of water level indicator it flow over and might come into the handle. Do not overfill when cleaning. -You will get the best result by brewing at least 4 cups. - Place the pipe in the percolator. -Place the desired amount of fine or coarse- ground coffee in the coffee container. Make sure that no coffee gets into the pipe. - Put the lid on the coffee container. - Put the lid on the percolator. -Plug in the percolator. The light will come on automatically when the coffee is ready. The coffee will keep hot as long as the percolator is plugged in. Rinse out your percolator carefully after use. The percolator must be used together with the original stand. NB: DO NOT WASH THE COFFEE POT IN A DISHWASHER For the best water throughflow: Clean the small coffee container regularly with washing up brush or wash it in a dishwasher! NB: If fine-ground coffee is used, some coffee grounds may end up in the bottom of the percolator. Let the coffee stand for a minute of so once brewed and any grounds will sink to the bottom. WARMING UP COFFEE If coffee is to be warmed up again the pipe and the coffee container must be removed from the coffee-pot. Then plug in the percolator and the coffee will be hot again in approx. 3-5 minutes. Never heat up more than 4 cups. DECALCIFYING - Mineral deposits can clog your percolator. To keep your percolator operating efficiently, you must regularly clean out mineral deposits left by the water; they can build up and clog your percolator. - Pour 1 quart of acetic acid into the pot. Then, add 3-quart cold water to the acetic acid. - Let the solution stay in the percolator for 10 minutes, then rinse the percolator by filling the pot with cold water. - Pour water into water tank and turn the percolator on. Repeat this procedure 3 times. - How often you need to descale your percolator depends on the hardness in the water. 11 ENVIRONMENTAL TIP An electronic appliance should, when it is no longer capable of functioning be disposed of with least possible environmental damage and according to the local regulations in your municipality In most cases you can discharge the appliance at your local recycling center. THE WARRENTY DO NOT COVER: -if the above points have not been observed. -if the appl...