Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Note: Before starting the machine after long periods of inactivity, the water circuit must be primed. Black Red • Turn the selector dial clockwise to set it to the “ ” position. The machine starts the automatic priming of the circuit by letting out a preset quantity of water through the steam/hot water wand (Pannarello, if supplied). The bar under the icon shows the operation progress. At the end of the priming process, the display shows an icon (see figure) indicating that the selection dial must be brought back to the central “ ” position. • The display then shows the machine warm-up icon, as shown in the fi gure. When warm-up is complete, the machine performs a rinse cycle of the internal circuits. In this phase, this icon will be displayed: • When the operations described above are complete, this icon will be displayed: The machine is then ready to brew beverages. • To brew coff ee, dispense hot water or steam, and for a proper use of the machine, carefully follow the instructions provided. If the machine is being used for the fi rst time or after a long period of inactivity, follow the operations described in the following section. • 31 • English Orange Green Green Green Red Using the machine for the first time or after a long period of inactivity. These simple operations will make it possible to always brew excellent coff ee. 1 Place a large container under the dispensing spout. 2 Before starting the procedure, check that the following icon is displayed. 3 Select the pre-ground coff ee function by pressing the “ “ button one or more times. Do not add the pre-ground coff ee to the compartment. The icon will appear on the display. 4 Press the button to brew a long coffee. 5 Wait until brewing is completed and empty the water tank. 6 Repeat the operations from step 1 to step 5 for 3 times; then continue with step 7. 7 Place a container under the steam wand (Pannarello, if supplied). 8 Turn the selector switch clockwise to set it to the “ ” position. The following icon will be displayed. 9 Dispense water until the no water signal is displayed, then turn the selector switch counter-clockwise to set it to the “ ” position. 10 At the end, fill the water tank again. Then the products can be brewed as described in the following sections. Rinse/Self-Cleaning Cycle This cycle will rinse coffee circuits with fresh water. The cycle is carried out: • At machine start (with cold boiler) • After priming the water circuit (with cold boiler) • During the stand-by mode (if a coff ee product has been brewed) • If the machine is turned off by pressing the ON/OFF button (if a coff ee product has been brewed). A small amount of water will be dispensed to rinse and heat all the machine components; in this phase this icon is displayed: Wait for the cycle to fi nish automatically. You can stop dispensing as well, by pressing either coff ee button and/or the ON/OFF button. • 32 • Intenza Water Filter To improve the quality of the used water, it is recommended that you install the water fi lter. Remove the small white filter from the tank and store it in a dry place sheltered from dust. Remove the water fi lter from its packaging, immerse it vertically (with the openings positioned upwards) in cold water and gently press its sides so as to let the air bubbles out. Set the Intenza Aroma System as specifi ed on the box. A = Soft water B = Hard water (standard) C = Very hard water Water hardness measurement The water hardness measurement is very important in order to correctly manage the “Intenza” fi lter and the frequency with which the machine must be descaled. Immerse the water hardness test strip provided with the machine in water for 1 second. Note: The test strip is only valid for one measurement. Check how many squares change colour and refer to the table. The letters correspond to the references that are located in the base of the Intenza fi lter. The fi lter must be adjusted based on this measurement. The numbers correspond to the settings that are found for the water hardness adjustment that is shown in the programming section. More precisely: 1 = (very soft water) 2 = (soft water) 3 = (hard water) 4 = (very hard water) Once this value is known, set the water hardness value as specified in the programming section. Insert the filter in the empty tank. The reference mark and the groove must match. Push fi rmly until it is completely inserted. Fill the tank with fresh drinking water and re-insert it into the machine. Dispense the water in the tank by using the hot water function (see section “Hot Water Dispensing”). Fill the water tank again. Press the ON/OFF button to change the machine status to stand-by mode. 2 3 4 A B C Intenza Aroma System Machine water hardness setting 1 Black Orange Orange Black Orange Orange When the icon appears, press the “ “ button to access the machine programming menu. Press the “ “ button until the following page is displayed. Press the “ “ button to select “ON” and press the “ “button to confi...
Este manual também é adequado para os modelos :Cafeteiras - RI9837/01 (8.06 mb)
Cafeteiras - RI9837/05 (8.06 mb)