Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
15 30 60 180 CALENDAR SETTINGS This menu allows you to programme the machine power-on times, according to your needs. The machine performs this function only if the power button is switched to on. It is possible to set 3 different power-on times, which can be managed independently. For reasons of brevity, only the "TIMER 1" setting is described below. The same setting procedure applies for the other timers. Note: The switch-off is managed through the "STAND-BY" programming. POWER-ON TIMER This menu allows you to adjust and set the first power-on time. timer 1 00:00 To set the hour for power-on. HOUR 00 MINUTES 00 To set the minutes of the power-on time. To set in which days of the week should the timer be active. Select a day using the () ro () buttons and confirm by pressing the (OK) button to modify the setting: ON = Time activated OFF = Time deactivated DAY OF THE WEEK ESCOK2.3.4.1.3 TIMER 1 00:00MONDAYTUESDAYWEDNESDAYTHURSDAYFRIDAYSATURDAYSUNDAYOFFOFFOFFOFFOFFOFFOFF This menu allows you to adjust and set the second power-on time. timer 2 00:00 This menu allows you to adjust and set the third power-on time. timer 3 00:00 MACHINE MENU WATER SETTINGS This menu allows setting correct water parameters for coffee brewing. WATER SETTINGS WATER HARDNESS To change the machine water hardness setting. The "Water Hardness" function allows adjusting the machine to the level of hardness of the water used. The machine will then request descaling at the right moment. Measure water hardness as shown on page 5. ENABLE FILTER To activate/deactivate the warning signal to replace the water filter. By activating this function, the machine notifies the user when the water filter needs to be replaced. OFF: Warning disabled. ON: Warning enabled (this value is automatically set when the filter is activated). ACTIVATE FILTER To activate the filter after its installation or replacement. Refer to the relevant section on page 7 to correctly install and/or replace the filter. MAINTENANCE SETTINGS This menu allows setting all the functions for correct machine maintenance MAINTENANCE SETTINGS PRODUCT COUNTERS This function shows how many products have been brewed for every single type of coffee since the last reset. DESCALING CYCLE This function enables the descaling cycle (the machine shows how many litres can be dispensed before descaling) (See page 35). This function enables the wash cycle for the brew group (See page 34). BREW UNIT CLEANING CYCLE This function enables the wash cycle for the carafe used for preparing milk beverages (See page 38). Note: This wash cycle is fundamental for a correct maintenance of the carafe. CARAFE WASH CYCLE CARAFE AUTO CLEAN This function enables automatic cleaning of the carafe after each dispensing of milk-based products. The self-cleaning function is disabled. off on The self-cleaning function is enabled. This function allows you to restore all factory settings. Note: By restoring the factory settings, all the personal parameters are lost. FACTORY SETTINGS MAINTENANCE FILL THE CARAFE HALFWAYWITH FRESH WATER AND INSERTIT IN BREWING POSITIONOK PLACE A CONTAINER UNDER HOTWATER & CARAFE DISP. SPOUTSOK EMPTY DRIP TRAY PLACEDUNDER THE BREW UNITOK 6 4 5 Fill half the carafe with fresh water (page 38 - fig. 7). Insert the carafe and place it in the brewing position. Then, press the "OK" button. Empty the drip tray placed under the dispensing spout (page 40 - fig. 2) and then replace it on the machine. Then, press the "OK" button. Place a container under the dispensing spout and a container under the hot water wand. Then, press the "OK" button. DESCALING CYCLEPAUSESTEP 1/2DESCALING CYCLE... DESCALING CYCLEPAUSESTEP 1/2DESCALING CYCLE... RINSE THE WATER TANK ANDFILL WITH FRESH WATER 8 9 7 The descaling cycle is activated. The bar shows the cycle's progress. If the containers need to be emptied, press the "Pause" button. Then, press the "START" button when the container has been emptied and replaced. At the end of the first step, when the descaling solution is finished, the machine will require a tank rinse. A default amount of water is needed for the rinsing step. This allows performing an ideal rinse cycle to ensure the best conditions to brew products. The message about filling the tank for the rinse cycle is normal, as it is part of the procedure. RINSE THE WATER TANK ANDFILL WITH FRESH WATEROK FILL THE MILK CARAFEWITH FRESH WATEROK EMPTY DRIP TRAY PLACEDUNDER THE BREW UNITOK 10 12 11 Rinse the water tank and refill it with fresh drinking water. Then, press the "OK" button. Completely empty the carafe (page 38 - fig. 7) and fill it with fresh water. Insert the carafe in the brewing position, and then press the "OK" button. Empty the drip tray placed under the dispensing spout (page 40 - fig. 2) and replace it back onto the machine. Then, press the "OK" button. DESCALING CYCLEPAUSESTEP 2/2RINSING CYCLE... DESCALING CYCLEPAUSESTEP 2/2RINSING CYCLE... PLACE A CONTAINER UNDER HOTWATER & CARAFE DISP. SPOUTSO...
Este manual também é adequado para os modelos :Cafeteiras - HD8943/12 (11.93 mb)