Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Depress hot water/brew switch (2) to pos. “1”. Espresso will start to flow into cups. 7 When cups are 3/4 full, release brew switch to “0”. The more water you allow to flow, the weaker the coffee. When properly made, the espresso will have a light brown foam “crema” floating on the top. If not, refer to “In the event of faulty function”. 8 Remove cups and serve. 9 To make more espresso, carefully and slowly remove the filter holder by moving handle to the left. Be careful as hot water will be on top of the coffee grinds in the holder. Some water will continue to drip from brewing head as filter holder is removed. That is normal and due to the pump pressure in the system. Knock out used coffee grinds from filter. For more espresso repeat steps 4 to 8 above OPTIONAL “Perfect crema” device (13) To ensure the optimum function of the “Perfect cream” device, insert the frothing jet device into the filter holder. We recommend that the “Perfect cream” device be cleaned on a daily basis, before use, in order to prevent any blockage of the delivery holes. A pin may be used to clean out the hole. Even if the type of coffee grinding is not correct the use of the “Perfect cream” device will produce the typical creamy froth of an espresso coffee. N.B.:Only use the “perfect cream device with a large 2-cup filter. Preparing cappuccino: When preparing to make a cappuccino, have all of the ingredients at hand as well as a frothing pitcher (or mug) halffilled with skimmed or low-fat milk and cups that are larger (6 oz.) than those used for espresso. Frothing Milk: The higher the fat content in the milk the denser the froth will be. The Turbo-Frother (8) or milk frother (24) will give you all the froth required but don’t let milk come to a boil. It may require two or three attempts to “become an expert” but you will be successful at frothing milk if you give it a chance. Swivel the Turbo- Frother steam nozzle (or milk frother) slightly outward so that you can get the frothing pitcher under the nozzle without knocking the base of the machine. Turbo frother steam nozzle version: 1 Make espresso (in a large cups) as described above 2 Position steam switch (4) to “1”. 3 After 15 to 20 seconds or, when temperature ready-light (3) goes on, place the frothing pitcher halffilled with low-fat milk under Turbo Frother steam nozzle so that tip is just under the surface of the milk. See Fig.03. • 11 • ENGLISH ENGLISH 4 Slowly turn steam valve knob (7) counter clockwise to release steam. IMPORTANT. The more you turn the knob, the greater the steam pressure for frothing. N.B.: Dispensing should not exceed 60 seconds. 5 Move pitcher in circular motion keeping the tip of steam nozzle just under surface of milk as it begins to froth. Do not let milk come to a boil since it will not froth. 6 When you have made enough froth,turn steam knob clockwise to shut off steam and remove pitcher. Put steam switch (4) to pos. “0”. 7 Spoon the froth onto the espresso in each cup and gently pour the hot milk along the side of the cup. Top each cup of cappuccino with a dash of cinnamon, cocoa and nutmeg. Serve. 8 NOTE: If you want to make more espresso immediately after steaming milk, the machine boiler must be refilled with water and temperature brought down to a brewing temperature. Otherwise, espresso may taste “burned”. To do this: place an empty cup on drip plate. Do not insert filter holder. Turn hot water/ brew switch (4) to “1” letting cup fill with water. Turn brew switch “0”. You many now proceed to make more espresso. OPTIONAL Milk frother (24) The milk frother (24) is a special device that allows an easy frothing by sucking milk directly out from its container. When preparing to make cappuccino, have all the ingredients at hand as well as a container of cold milk and cups that are larger than those used for espresso. Make sure that the milk frother (24) is correctly mounted on the steam nozzle (A) by turning the ring nut (B), and place the suction pipe (C) into the cold milk container. It is possible to adiust the amount of milk that is sucked up by means of the bar (D). The position that is shown in the picture indicates the maximun suction, milk is lukewarm. By turning the bar (D) 180°, the minimum suction is set,and milk is warmer. Milk frother version: 1 Make espresso (in large cups) as described above. 2 Depress steam switch (4) to “1”. 3 After 10 to 15 seconds or when the temperature ready-light (3) goes on, place the suction pipe (C) into the cold milk container and the cup containing the espresso under the milk frother (24) . • 12 • ENGLISH • 13 • Keeping it clean: 1 IMPORTANT: the steam nozzle should be cleaned after each use in order to avoid build up of milk deposits that are very difficult to clean. Cleaning is made easy as can be seen in the DESCRIPTION OF PARTS. The outer part of nozzle can be removed by pulling downward. The outside of the steam pipe can be cleaned with a damp cloth. The steam jet is cleaned by running a shot of ste...