Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
PREPARING ESPRESSO BY USING MANUAL FUNCTION WITH COFFEE POWDER Espresso can be also obtained by using manual espresso function. This allows you to obtain the quantity of coffee that meets your need. Follow the instruction 1-4 in “PREPARING ESPRESSO BY USING PRESET FUNCTION WITH COFFEE POWDER”. Press the manual espresso button (10) to start brewing the coffee. To stop the flow of coffee, press the button (10) again. ATTENTION: Do not try to release the filter holder while button (10) or button (11) is on. Given that the coffee maker is fitted with a self-priming system there is no special procedure to carry out when the tank runs out of water or after a prolonged period where the coffee maker has not been used. SET THE TEMPERATURE OF ESPRESSO The coffee maker provides 2 espresso temperature alternatives: normal or very hot espresso. To set the very hot espresso, press the espresso temperature button (12), the ON/OFF button (9) will flash. When the ON/OFF button (9) stops flashing, operate the preset or manual espresso button as usual. To set normal espresso, keep the espresso temperature button (12) at OFF mode (The espresso temperature button lamp is off). CHANGE PRESET ESPRESSO QUANTITY With this coffee maker you can adjust the cup sizes to your taste. The factory-preset quantities are: 1 cup = approx. 30ml 2 cups = approx. 60ml You can freely adjust the cup size: 1 cup = at least 30ml. Recommendation 35ml – 65ml 2 cups = at least 60ml. Recommendation 95ml – 125ml There is no maximum quantity but the coffee will lose strength and taste the more water you add. The programming can be completed while an espresso is being made. Follow the instruction 1-4 in “PREPARING ESPRESSO BY USING PRESET FUNCTION WITH COFFEE POWDER”, then press and hold the preset espresso button (1 cup espresso or 2 cups espresso depending on which one is to be programmed) until you obtain the desired espresso quantity. The programming is completed. NOTE: The brewing time for programming should not be less than 9 seconds; otherwise the minimum quantity will not be reached and the programming may not be completed. Reset to the factory-programmed quantity Press and hold 1 cup preset espresso button, and then press and hold the ON/OFF button (keep both buttons pressed and held). After 10 seconds, set the ON/OFF button free and then set the 1 cup preset espresso button free. The 1 cup preset espresso mode has been reset to the factory programmed quantity. If the 2 cup preset espresso mode needs to be reset, do the same but press the 2 cups button. PREPARING ESPRESSO WITH COFFEE PODS Apart from ground coffee this coffee maker can also use single portions of coffee. There are two types of coffee pod available in the market: A - 60mm flexible (loose) coffee pods, suitable for drip-fed coffee makers and percolators B - 44mm packed coffee pods, especially for espresso machines Your coffee maker will not operate correctly with 60mm flexible coffee pods as they do not fit properly in the filter holder. Always use packed coffee pods of approximately 44mm diameter with this coffee maker, see Fig. 2c. These single coffee pods can be found at your usual retailers. Fit the all-in-one filter into the filter holder. Put 1 coffee pod into the filter. Place the rubber ring on top the coffee pod. NOTE: When using the rubber ring to make espresso with espresso pods, make sure that the side with the dot is facing downwards (toward the pod). Then follow steps 3-4 of the instructions for making espresso with coffee powder. (Fig. 2c) PREPARING CAPPUCCINO The steam can be used for warming the cups, heating liquids or preparing hot frothed milk for cappuccino coffee. Remove the filter holder before using the steam, as this will stop the inside of the filter from becoming overpressurized. 1. Fill cold milk into a jug. Make sure that the ON/OFF button (9) has been switched on and is flashing (Fig. 7). Press the steam button (13). When the ON/OFF button stops flashing, the right temperature for steam will have been reached. 2. Place a container below the steam nozzle (3) and turn the steam regulator (14) in an anti-clockwise direction (Fig. 4). After any water left in the nozzle has been cleared out, close it. Insert the nozzle into the jug of milk and turn the steam regulator back on so that steam comes out (Fig. 5). 3. Move the jug up and down slightly. Avoid letting the liquid go beyond the end of the nozzle as this will stop air from being drawn in. Place the steam pipe just above the surface of the milk in order to make it frothy. Add the frothed-up milk to the coffee. IMPORTANT: After making froth clean off any milk left stuck to the nozzle. Giving it a further short burst of steam will help to clean it. 4. Clean the steam nozzle regularly with the appliance unplugged and cold (Fig. 6). Remove the sleeve (3a) from the steam pipe (3) and clean out the nozzle with soft damp cloth. The sleeve can be washed under running tap water. SWITCHING FROM CAPPUCCINO TO ESPRE...