Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
(factory setting: On). > Water filter: Each time a new water filter is inserted in the water tank (12), it must be rinsed: 1. Place the water filter in the water tank (12) and fill the tank with water up to the “max” mark. 2. Turn the rotary knob (4) to select Press start and press start stop (8). 3. Place a container with a capacity of 0.5 litres under the milk frother (10). 4. Press start stop (8). Water will now run first through the filter to rinse it and then into the container. deen deen Empty the container. The appliance is ready to use once more. Rinsing the filter simultaneously activates the setting for the Service -change filter display. The filter is no longer effective when the Service -change filter display appears, or at the latest after two months. It needs to be replaced for reasons of hygiene and so that there is no build-up of limescale (this could damage the appliance). Replacement filters can be obtained from retailers or customer service (see “Accessories”). After every filter change the filter must first be rinsed. Proceed as described at the beginning of this section. If no new filter is used, turn the water filter setting to Off. You can find detailed information about the water filter in the enclosed filter instructions. If the appliance has not been used for a prolonged period (e.g. during your vacation) the filter should be rinsed before the appliance is used again. To do this, simply dispense a cup of hot water. Further entries in the Settings menu: > Descaling program: If you want to descale the appliance, press start stop (8) and run the descaling programme (see “Descaling”). > Cleaning program: If you want to clean the appliance, press start stop (8) and run the cleaning programme (see “Cleaning”). > Calc‘n‘Clean: If you want to descale and clean the appliance at the same time, press start stop (8) and run the Calc‘n‘Clean programme (see “Calc‘n‘Clean“). > Factory settings: You can cancel your own settings and reset the factory settings. To activate the factory settings, press start stop (8). The appliance can also be reset to the factory settings as follows: 1.Switch the appliance off fully at the power switch O/I (1). 2.Press < and > (3) at the same time, hold them down, and switch the appliance on again at the power switch O/I (1). The factory settings are reactivated. Set percup quantity The per-cup quantity can be adjusted individually to suit your cups. It can be set separately for each type of drink and each cup size. 1. To call up the default settings, keep i (7) depressed for at least 3 seconds. 2. Select Per -cup quantities with > 3. Press start stop (8). 4. Select the type of drink with the rotary knob (4). 5. Press >. 6. Select the cup size with the rotary knob (4). 7. Press >. 8. Set the per-cup quantity with the rotary knob (4). < returns you to cup size and drink selection. To quit the default settings, press i (7). The settings are stored. When the cup size is selected, the changed per-cup quantity is shown graphically: 1x *1x+Coffee Per-cup quantity reduced compared with standard setting Per-cup quantity increased compared with standard setting Standard deen deen Important: The selected amount in ml is an approximate value and can vary significantly as a result of crema forming, the grind setting or the type of milk used, etc. Adjusting the grinding unit The rotary selector (16) on the top of the appliance adjusts the degree of grinding from coarse to fine as required. 16 Warning: Adjust the grinding unit only while it is running. Otherwise the appliance may be damaged. 1. Deploy the appliance fully (see “Deployment system”). 2. In the drink selection menu, select Espresso. 3. Press start stop (8). 4. While the grinding unit is running, adjust the rotary selector (16) from fine to coarse or back as required. The new setting will not become apparent until after the second cup of coffee. For dark roast coffee beans, choose a finer grind, for lighter beans a coarser grind. Checking the water hardness The water hardness setting can be adjusted on this appliance. It is important to set the water hardness correctly, so that the appliance indicates accurately when the descaling programme should be run. The factory setting for the water hardness is 4. You can check the water hardness using the enclosed test strip or by asking your local water supplier. Dip the test strip briefly in water, gently shake off any drips, and check the result after one minute. Water hardness levels and settings: Level Water hardness German (°dH) French (°fH) 1 1-7 1-13 2 8-14 14-25 3 15-21 26-38 4 22-30 39-54 Tips on energy saving > Press on off (2) to switch the appliance to “energy saving mode”. The appliances uses very little power when in “energy saving mode”, but monitors all safety-relevant functions so as to avoid damage. • After one hour (factory setting), the appliance switches off automatically and does not consume any more energy. The default time of one hour can be shortened (s...
Este manual também é adequado para os modelos :Cafeteiras - TK76K573/09 (2.32 mb)
Cafeteiras - TK76K573GB/08 (2.32 mb)
Cafeteiras - TK76K573GB/09 (2.32 mb)