Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
If the LED does not light up when the system is powered on, try reversing the connection. For more information on connecting LEDs to your motherboard, see your motherboard user’s manual. Front panel leads Note: Polarity (positive and negative) does not matter for switches. 3.4 Rewiring Motherboard Header Connections There may come a time when you need to reconfigure the pin-out of a motherboard header connector. Examples could be for your USB header, audio input header, or some other front panel connector such as the Power Button connector. Before performing any work, please refer to your motherboard user’s manual or your motherboard manufacturer's website to confirm the pin-out needed for your connector. We strongly recommend making a notated drawing before beginning work so that you can recover if your work gets disturbed. Front panel headers Determine which wires you need to remove in order to rewire your plug to match the USB pin-outs on your motherboard (refer to your motherboard user’s manual). Working on one connector at a time, use a very small flathead screwdriver or similar tool to lift up on the black tab located beside the gold posts (squares). This will allow you to easily slide out the pins from the USB plug. Working carefully so as not to damage the wires, connectors, or pins, slowly remove the pin from the connector. Repeat these steps for each wire you need to change. Working carefully so as not to damage the wires, connectors or pins, slowly insert the pin into the correct slot of the connector then snap closed the black tab that was lifted in step 1. Repeat these steps for each wire you need to change. Section 4 Cooling System One / One S / One S3 User Manual 4.1 Included Fans One: The One comes with two standard fans (yellow outline) – a rear 120 mm exhaust fan and a top 120 mm exhaust fan. The red rectangles indicate additional fan mounts. Mounting procedures for these fans is discussed in Section 4.2. One fan locations One S / One S3: The One S and One S3 come with one standard fan (yellow outline) – a top 120 mm blue LED exhaust fan. The red rectangles indicate additional fan mounts. Mounting procedures for these fans is discussed in Section 4.2. One S / One S3 fan locations 120 mm Single Speed Fan Specifications Size: 120 x 25 mm fan Rated Voltage: 12V Operating Voltage: 10.8V ~ 13.2V Speed (RPM) Input Current Airflow Static Pressure Acoustic Noise Input Power 1200 0.20A (Max.) 1.2 m. / min (42.6 CFM) 1.0 mm-H2O (0.04 inch-H2O) 23.7 dBA 2.4W 4.2 Optional Fans One: The One includes mounts for up to three more fans. These mounts are as follows: - 1 x front intake 120 mm mount - 1 x side 120 mm mount - 1 x bottom 120/140 mm mount One S / One S3: The One S / One S3 includes mounts for up to four more fans. These mounts are as follows: - 1 x front intake 120 mm mount - 1 x side 120 mm mount - 1 x bottom 120/140 mm mount - 1 x rear 120 mm mount Front intake 120 mm fan 1. Remove the front bezel as outlined in Section 2.2. 2. Align the fan with the screw holes and screw in the fan in the top-left and lower-right holes (as pictured). 3. Screw in the long fan screws (E in Section 1.3). Screw in the fan in the top-left and lower-right holes. Side 120 mm fan On the left panel, there is a 120 mm fan mount for additional graphics cards cooling. 1. Remove the left side panel as outlined in Section 2.2. 2. Align your fan with the mounting holes. The fan should be installed with air blowing into the case. 3. Screw in the fan with the included screws (H in Section 1.3). Screw the side fan into place by first aligning it with the fan screw holes. Bottom 120/140 mm fan At the base of the case, there is a fan mount that can fit either a 120 mm or 140 mm fan for additional air intake. 1. Remove the left side panel as outlined in Section 2.2. Rest the case on its side so you have access to both sides of the fan mount. 2. Align your fan with the mounting holes. The fan should be installed on the inside of the case, with air blowing in. 3. Screw in the fan with the included screws (H in section 1.3). Screw the bottom fan into place by first aligning it with the bottom screw holes. Rear 120 mm fan – One S / One S3 only A rear exhaust fan can be installed for additional airflow out of the case. 1. Remove the left side panel as outlined in Section 2.2. 2. Align your fan with the mounting holes. The fan should be installed with air blowing out of the case. 3. Screw in the fan with the included screws (H in section 1.3). Screw the rear fan into place by first aligning it with the rear screw holes. 4.3 PSU Air Filter The One / One S / One S3 features a PSU air intake filter that can be removed and cleaned. To remove the PSU filter: 1. Pull the filter out toward you using the tab at the back of the chassis. Pull the filter toward you using the tab outside the chassis. Antec, Inc. 47900 Fremont Blvd. Fremont, CA9...
Este manual também é adequado para os modelos :Acessórios de computador - ONE S3 (866.09 kb)
Acessórios de computador - ONE (866.09 kb)