Ensure that you have the appropriate SFP installed for your cables. See the Adaptec 2U Storage Enclosure Installation and User’s Guide on the CD for more cabling information and for daisy-chaining instructions. Single Loop Configuration FC4100 FC I/O Module OUTPUT INPUT HOST BUS ADAPTERDaisy-chain to next FC4100 Dual Loop Configuration OUTPUT INPUT HOST BUS ADAPTERDaisy-chain to next FC4100 FC4100 FC I/O Module OUTPUT INPUT HOST BUS ADAPTERDaisy-chain to next FC4100 FC4100 FC I/O Module 9 Connec

If you select this option and press , the values entered in the setup utilities will be recorded in the chipset’s CMOS memory. The microprocessor will check this every time you turn your system on and compare this to what it finds as it checks the system. This record is required for the system to operate. Exit without savin. Selecting this option and pressing lets you exit the Setup program without recording any new values or changing old ones. 50 SBC-596/599 User's Manual CHAPTER

Card with LCD, Ethernet, SCS. & High Driv. Copyright Notic. This document is copyrighted, 1998. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliab

Continue with Step 2: Installing the Drive Carriers, below. Step 2: Installing the Drive Carriers These instructions assume that the drive carriers have already been attached to your disk drives. ! Caution: Acclimate new disk drives to room temperature before you install them and power up the Storage Enclosure. To install the drive carriers into the Storage Enclosure: Hold the drive carrier with the LEDs on the left side (at the bottom for tower-mounted systems) and select an open disk drive slo

Check the length between the front and rear supports of your equipment rack and determine which set of rear rails to use, the long or the short. 3 3 Secure the rear rails you selected to the rear supports of the equipment rack, using the supplied screws, as shown in the Figure in Step 1 on page 3. 4 Secure the front rails to the rear rails, as shown below. 5 Tighten all the screws before continuing. 6 With assistance from a second person, lift the Storage Enclosure and slide the rear of the encl

See your Adaptec reseller for purchase information. Installation Checklist . Read and follow the safety tips. See page 2. . Install the enclosure in an equipment rack or tower assembly (optional.) See page 2. . Install the drive carriers. See page 6. . Set the drive slot and enclosure IDs. See page 7. . Connect the I/O cables. See page 7. . Connect the AC power cords to the APC modules. See page 11. . Follow the instructions in Next Steps on page 11. 1 Safety Tips ! Caution: A fully loaded enclo

Microsoft and Windows are registered trademarks of Microsoft Corporation in the US and other countries, used under license. Apple and Macintosh are trademarks of Apple Computer, Inc. in the US and other countries, used under license. All other trademarks are the property of their respective owners. Changes The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accurac

¦ Increase the separation between equipment and receiver. ¦ Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ¦ Consult the dealer or an experienced radio/television technician for help. ¦ Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this unit to the specified limits of the rules. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device

2 Restart your computer. 3 When the Red Hat Welcome screen displays, type linux dd at the Boot: prompt. 4 When prompted, insert the driver disk, then select OK. 5 Follow the prompts to set up the environment you want. 6 If you are installing other third-party devices, install them now. Otherwise, select Done. 7 Complete the Red Hat Linux installation, following the instructions included with your operating system. 8 Continue with Managing Your Storage Space on page 41. Installing with SuSE Linux

Creating an Array with the ACU The ACU is menu-based and instructions for completing tasks display on-screen. Menus can be navigated using the arrows, Enter, Esc, and other keys on your keyboard. Before creating arrays, make sure the disks for the array are connected and installed in your system. Disks with no usable space are shown in gray and cannot be used. See Physical Devices View on page 46. To create an array: 1 Turn on your computer and press Ctrl+A when prompted to access the ARC utilit