Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient the receiving antenna • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Notes: • Unauthorized changes or modifications may void the user's right to operate the equipment. • Only equipment certified to comply with Class B (computer input/output devices, terminals, printers, etc.) should be attached to this equipment and all such equipment must be connected with shielded interface cable. • Voltage Selection Switch /...... Select the correct voltage setting for your local area voltage before the computer system is plug to the power source. ..................... 110V. WARNING: Select incorrect setting will cause the Power supply failure! ..:.......,...........! V. Installing the System / ...... 1. Unscrew the rear casing and push the upper casing toward the front panel, then loose the hook to remove the front panel. ....... 3...,..........,............ For Model VB3 only / VB3....: Unscrew the black bar and remove it either. ...........,...... 2. After loosening the 3 front screws, pull out the Device disk Bay. ...... 3....,............. 3A. For Model VB2 / VB2..: Put the hard disk drive & DVD-ROM into the rack, and align the screws at the screw holes. .............,............ 3B. For Model VB3 / VB3..: Put the floppy disk drive & DVD-ROM into the rack, and align the screws at the screw holes. .............,............ 4. CPU / ..... 4-1. Evenly spread the heat dispersion paste on the CPU and make sure it totally cover the CPU. Insert the CPU on the CPU socket. Make sure that you have lifted the transversal lever and aligned the aslant side of the CPU along the aslant side of the CPU socket. After CPU is secured tightly onto the CPU socket, release the transversal lever and attach it to the CPU socket. ......... CPU.,........ CPU.. CPU....... CPU... ........,.. CPU.... CPU.......... CPU. CPU.... ....,......... CPU... CPU Pin Evenly spread the heat dispersion paste on the CPU / ......... CPU. Lift the transversal lever /.... A. For Model VB2 / VB2..: Click the heat sink locker to the motherboard retention module. ............. Install fan on top of CPU /. CPU.... CPU. B. For Model VB3 / VB3..: Latch the hooks on both sides of the CPU securely into the CPU socket / .. ...... .... CPU .. Fix the cooler on the rack / .CPU.....CPU. For Model VB3 only / VB3 ....: Align the screws at the black bar’s screw holes. Push the hard disk drive into the rack and align the screws at the screw holes, including 2 screws holes on the black bar. ................. ................., ................. .............,.... .. 6. Connecting the IDE bus cable / ..IDE...... A. For Model VB2 / VB2..: Take out the IDE bus cables bundled in the accessory kit. Connect the black connector to the hard disk drive and option devices, and align the first pin of the red cable to Pin 1 labeled on the hard disk and option devices. ....... IDE......,.................,....... ..................... 1.... HDD / ... ODD / ..... • Note: If the first pin of the red cable doesn’t align to Pin 1 labeled on the hard disk and option devices, your hard disk and option devices will not work and may cause damage to the disk. ..:.............................. 1.. .,....................... B. For Model VB3 / VB3..: Take out the IDE bus cables bundled in the accessory kit. Connect the black connector to the hard disk drive and floppy disk drive / option devices, and align the first pin of the red cable to Pin 1 labeled on the hard disk and floppy disk / option devices. .......IDE......,.............. /......,.... ................../.........1.... HDD / ... ODD / ..... FDD / ... • Note: If the first pin of the red cable doesn’t align to Pin 1 labeled on the hard disk and floppy disk drive / option devices, your hard disk and floppy disk drive / option devices will not work and may cause damage to the disk. ..:......................../......... 1 ...,......../.................. 7. Connecting the power supply / ....... A. For Model VB2 / VB2..: Connect the connector of the power supply to the power supply socket of the hard disk drive and option device. Follow above note. ..................................... HDD / ... ODD / ..... B. For Model VB3 / VB3..: Connect the connector of the power supply to the power supply socket of the hard disk drive and floppy disk drive / option device. Follow above note. ...................../................... HDD / ... ODD / ..... FDD / ... ...