Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
6. Replace the optical drive (see Replacing the Optical Drive). 7. Replace the top bracket (see Replacing the Top Bracket). 8. Replace the top cover (see Replacing the Top Cover). 9. Connect your computer and all attached devices to electrical outlets, and turn them on. Back to Contents Page 1 drive bay 2 screws (2) 3 hard-drive cable CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. Back to Contents Page Processor Heat Sink Dell™ Inspiron™ 410 Service Manual Removing the Processor Heat Sink Replacing the Processor Heat Sink Removing the Processor Heat Sink 1. Follow the procedures in Before You Begin. 2. Remove the top cover (see Removing the Top Cover). 3. Remove the top bracket (see Removing the Top Bracket). 4. Remove the optical drive (see Removing the Optical Drive). 5. Remove the drive bay (see Removing the Drive Bay). 6. Loosen the four captive screws that secure the processor heat sink to the system board. 7. Carefully lift the processor heat sink away from the computer. 8. Lay the processor heat sink down on its top, with the thermal grease facing upward. Replacing the Processor Heat Sink WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at WARNING: The heat sink may be very hot during normal operation. Be sure that it has had sufficient time to cool before you touch it. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on your computer). CAUTION: Do not perform the following steps unless you are familiar with hardware removal and replacement. Performing these steps incorrectly could damage your system board. For technical service information, see the Setup Guide. CAUTION: To ensure maximum cooling for the processor, do not touch the heat transfer areas on the processor heat sink. The oils in your skin can reduce the heat transfer capability of the thermal grease. 1 captive screws (4) 2 processor heat sink 1. Follow the procedures in Before You Begin. 2. Clean the thermal grease from the bottom of the processor heat sink. 3. Apply the new thermal grease to the top of the processor. 4. Align the four captive screws on the processor heat sink with the screw holes on the system board and tighten the screws. 5. Replace the drive bay (see Replacing the Drive Bay). 6. Replace the optical drive (see Replacing the Optical Drive). 7. Replace the top bracket (see Replacing the Top Bracket). 8. Replace the top cover (see Replacing the Top Cover). 9. Connect your computer and devices to electrical outlets, and then turn them on. Back to Contents Page CAUTION: Incorrect alignment of the processor heat sink can cause damage to the system board and processor. NOTE: The original thermal grease can be reused if the original processor and processor heat sink are reinstalled together. If either the processor or the processor heat sink is replaced, use the thermal grease provided in the kit to ensure that thermal conductivity is achieved. CAUTION: Ensure that you apply new thermal grease. New thermal grease is critical for ensuring adequate thermal bonding, which is a requirement for optimal processor operation. CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. Back to Contents Page I/O Bracket Dell™ Inspiron™ 410 Service Manual Removing the I/O Bracket Replacing the I/O Bracket Removing the I/O Bracket 1. Follow the procedures in Before You Begin. 2. Remove the top cover (see Removing the Top Cover). 3. Remove the top bracket (see Removing the Top Bracket). 4. Remove the bottom cover (see Removing the Bottom Cover). 5. Remove the I/O bezel (see Removing the I/O Bezel). 6. Remove the three screws that secure the chassis fan to the I/O bracket. 7. Using a hex nut driver, remove the two hex nut screws that secure the VGA connector to the I/O bracket. 8. Remove the screw that secures the I/O bracket to the chassis. 9. Release the I/O bracket out of the computer cover and lift the I/O bracket out of the computer. Replacing the I/O Bracket 1. Follow the procedures in Before You Begin. 2. Align and insert the tabs on the bottom of the I/O bracket into the slots on the chassis. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at CAUT...