Assessments - , GPA:
(
)
)
Fabricante : Dell
Arquivo Tamanho: 1.15 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
por este dispositivo também tem outras instruções :
Facilidade de uso
© 2000 Dell Computer Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trademarks used in this text: Dell Precision and the DELL logo are trademarks of Dell Computer Corporation; Microsoft and Windows NT are registered trademarks of Microsoft Corporation; Intel and Pentium are registered trademarks and Xeon is a trademark of Intel Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own. Initial release: 8 Feb 2000 Last revised: 26 Oct 2000 Removing and Replacing Parts NOTE: You can obtain the latest version of this document from the Support section of the Dell Web site at Notes, Notices, and Cautions Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, notices, and cautions, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your system. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Back to Contents Page Removing and Replacing Parts: Dell Precision™ WorkStation 620 Systems Service Manual Overview This section provides procedures for removing and replacing the components, assemblies, and subassemblies in the Dell Precision WorkStation 620 system. Unless otherwise noted, each procedure assumes that the following conditions exist: l You have performed the steps in "Precautionary Measures." l You have removed the computer cover. l You can replace or reinstall a part by performing the removal procedure in reverse order unless additional information is provided. Recommended Tools Most of the procedures in this file require the use of one or more of the following tools: l Wide flat-blade screwdriver l #2 Phillips-head screwdriver l 1/4-inch nut driver l A wrist grounding strap as explained in "Precautionary Measures." Precautionary Measures Before you perform any procedure in this section, take a few moments to read the following caution for your personal safety and to prevent damage to the system from electrostatic discharge (ESD). Overview Expansion Cards Recommended Tools Expansion-Card Guide and Fan Precautionary Measures Control Panel Restarting the System Chassis Intrusion Switch Computer Cover Power Supply Interior Service Label System Board Components Internal View Memory Front Panel Microprocessor/Heat Sink Assembly Front-Panel Inserts Cooling Fan Drives Battery AGP Pro Card Brace System Board CAUTION: FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE EQUIPMENT Before you start to work on the system, perform the following steps in the sequence listed: 1. Turn off the computer and all peripherals. Restarting the System To restart the system and reset the chassis intrusion detector, perform the following steps: 1. Replace the computer cover and reconnect the computer and peripherals to their power sources and turn them on. ALERT! Cover was previously removed. 2. To reset the chassis intrusion detector, enter System Setup, select System Security, and reset Chassis Intrusion to Enabled, Enabled- Silent, or Disabled. Computer Cover Figure 1. Padlock Ring Release To remove the computer cover, perform the following steps: 1. Turn off your computer and peripherals, and observe the Caution for Your Personal Safety and Protection of the Equipmentdescribed in "Precautionary Measures." 2. If you have installed a padlock through the padlock ring on the back panel, remove the padlock. 3. Face the back of the computer and slide the upper half of the padlock ring to the left to unlock the cover release mechanism (see Figure 1). 4. Face the left side cover and press the release button (located at the bottom-left corner of the front panel) (see Figure 2). 2. Disconnect the computer and peripherals from their AC power sources. Also, disconnect any telephone or telecommunication lines from the computer. Doing so reduces the potential for personal injury or shock. 3. To avoid possible damage to the system board, unplug the computer system and wait 15 to 30 seconds before removing a component from the system board or disconnecting a peripheral from the computer. 4. Wear a wrist grounding strap, and clip it to an unpainted metal surface, such as the padlock loop on the back of the chassis. If a wrist grounding strap is not available, touch any unpainted metal surface on the back of the computer or on the computer chassis, such as the power supply, to discharge any static charge from your body before touching anything inside the computer. While you work, periodically to...