Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
NOTICE: When you place the microprocessor in the socket, ensure that all of the pins fit into the corresponding holes on the socket. 4. Set the microprocessor lightly in the socket and ensure that all pins are headed into the correct holes. Do not use force, which could bend the pins if the microprocessor is misaligned. When the microprocessor is positioned correctly, press it with minimal pressure to seat it. 5. When the microprocessor is fully seated in the socket, pivot the release lever back toward the socket until it snaps into place to secure the microprocessor. If you are installing a microprocessor replacement kit from Dell, return the microprocessor to Dell in the same package in which your replacement kit was sent. 6. Reinstall the two screws that attach the blower to the heat sink. 7. Install the heat-sink/blower assembly: a. Place the one end of the heat-sink assembly under the tab on one side of the retention base. b. Lower the assembly until the heat sink fits securely under the tab on the retention base. c. Insert the securing clip by placing the notched end of the clip opposite the tab into the slot on the retention base. Press on the securing clip tab and lower the securing clip into place. Make sure that the notched ends of the securing clip are secured in the retention base slots. 8. Plug the fan cable into the FAN1 connector on the system board. 9. Plug the power cable into the 12VPOWER1 connector on the system board. 10. Close the computer cover. 11. Attach the computer stand (optional). 12. Connect your computer and devices to electrical outlets, and turn them on. Back to Contents Page NOTICE: If you are not installing a microprocessor upgrade kit from Dell, reuse the original heat-sink/blower assembly when you replace the microprocessor. NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer. Back to Contents Page Technical Specifications Dell™ Dimension™ 4600C Service Manual Microprocessor System Information Expansion Bus Memory Drives Ports and Connectors Video Audio Network Controls and Lights Power Physical Environmental Microprocessor Microprocessor type Intel® Pentium® 4 with HT Technology that runs at 2.40, 2.60, 2.80, 3.00, or 3.20 GHz internally and 800 MHz externally or 2.26, 2.40, 2.53, 2.66, 2.80, or 3.06 GHz internally and 533 MHz externally NOTE: Not all Pentium 4 processors support Hyper-Threading technology. Intel Celeron® D processor 325, 330, or 335 NOTE: Dell™ Dimension™ 4600C computers with Intel Celeron processors are available only in Japan. L1 cache 8 KB first-level L2 cache 256-KB, 512-KB, or 1-MB pipelined-burst, eight-way set associative, write-back SRAM System Information System chip set Intel 865G DMA channels four Interrupt levels 24 APIC mode System BIOS chip 4 Mb (512 KB) System clock 533- or 800-MHz quad-data rate Expansion Bus Bus types PCI and AGP Bus speed PCI: 33 MHz AGP AGP 1X, 4X, 8X AGP connector one low profile AGP connector size 172 pins AGP connector data width (maximum) 32 bits AGP video bus protocols 4x mode at 1.5 V PCI connectors one low profile PCI connector size 120 pins PCI connector data width (maximum) 32 bits Memory Architecture DDR SDRAM Memory connectors two Memory capacities 128-, 256-, 512-MB, and 1-GB non-ECC DDR SDRAM Minimum memory 256 MB Maximum memory 2 GB Memory type 333-MHz DDR SDRAM (non-ECC) NOTE: DDR 333 memory performs at 266 MHz on 400 front- side bus processors. Drives Externally accessible one slimline optical bay one slimline 3.5-inch bay Internally accessible one bay for 1-inch–high IDE hard drive Ports and Connectors Externally accessible: Parallel 25-pin connector (bidirectional) IEEE 1394 (optional) two 4-hole, unpowered connectors Video 15-pin connector Keyboard 6-pin mini-DIN connector or USB connector Mouse 6-pin mini-DIN connector or USB connector USB two front-panel and six back-panel USB 2.0-compliant connectors Headphone front-panel miniature connector for line-out Audio five back miniature connectors for line-in, line-out, microphone, and surround and center/Low-Frequency Effects (LFE) channel S/PDIF one back-panel digital line-out connector Network RJ-45 connector Internally accessible: Primary IDE channel 40-pin connector on PCI local bus Secondary IDE channel 40-pin connector on PCI local bus Serial ATA one 7-pin connector Video Video controller integrated Intel® Extreme Graphics 2 (low-profile AGP video card also supported)—4X and 8X Audio Audio controller ADI 1980 integrated 5.1 channel audio Network Network controller integrated 10/100 Ethernet Controls and Lights Power control push button Power light green light on power button—blinking green in sleep state; solid green for power-on state Hard-drive access light green Diagnostic code lights four bicolor (amber and green) located on back panel Power DC power supply: Wattage 160 W Heat dissipation 546 BTU (fully-loaded computer without monitor) Voltage (see your Owner's Manual for impo...