Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Code Cause 1-3-1 through 2-4-4 Memory not being properly identified or used 4-3-1 Memory failure above address 0FFFFh If you hear one of the following beep codes, see "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. Code Cause 1-1-2 Microprocessor register failure 1-1-3 NVRAM 1-1-4 ROM BIOS checksum failure 1-2-1 Programmable interval timer 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 3-1-1 Slave DMA register failure 3-1-2 Master DMA register failure 3-1-3 Master interrupt mask register failure 3-1-4 Slave interrupt mask register failure 3-2-2 Interrupt vector loading failure 3-2-4 Keyboard Controller Test failure 3-3-1 NVRAM power loss 3-3-2 NVRAM configuration 3-3-4 Video Memory Test failure 3-4-1 Screen initialization failure 3-4-2 Screen retrace failure 3-4-3 Search for video ROM failure 4-2-1 No time tick 4-2-2 Shutdown failure 4-2-3 Gate A20 failure 4-2-4 Unexpected interrupt in protected mode 4-3-3 Timer-chip counter 2 failure 4-3-4 Time-of-day clock stopped 4-4-1 Serial or parallel port test failure 4-4-4 Cache test failure System Messages NOTE: If the message you received is not listed in the table, see the documentation for either the operating system or the program that was running when the message appeared. Message Possible Cause Corrective Action 8A02042 e Grartoer- The keyboard controller failed its test. If you receive this message after you make changes in the system setup program, enter the system setup program and restore the original value(s). ASdhdorret!ss Line An error in the address decoding circuitry in the memory has occurred. Reseat the memory modules. CE:rr oDrrive CF:ai lDurrieve The hard drive is not working or is not configured correctly. Ensure that the drive is installed correctly in the computer and defined correctly in the system setup program. CMaecmhoery Bad, DEnoa bNloet Cache The cache memory is not operating. See "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. CEHrr-o2r Timer An error is occurring on the timer on the system board. See "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. CSMtOaSte B aLtotwery The system configuration information in the system setup Enter the system setup program, verify the system configuration, and then restart the CCMhOeScksum Failure COMpOtSio Snyss tNeomt Set CTMyOpSe Display Mismatch CSMiOzSe Memory Mismatch CaMnOdS D Taitmee Not Set program is incorrect or the battery charge may be low. computer. BDiooskte Ftatielure Drive A or B is present but has failed the BIOS POST. Ensure that the drive is installed correctly in the computer and defined correctly in the system setup program. Check the interface cable at both ends. DMA Error DMA 1 Error DMA 2 Error Error in the DMA controller on the system board. The keyboard or system board may need to be replaced. CFDoDntroller Failure CHDoDntroller Failure The BIOS cannot communicate with the floppy drive or hard drive controller. Ensure that the drive is installed correctly in the computer and defined correctly in the system setup program. Check the interface cable at both ends. INTR1 Error INTR2 Error An interrupt channel on the system board failed to POST. The keyboard or system board may need to be replaced. DIinsvakelitdte Boot The operating system cannot be located on drive A or drive C. Enter the system setup program and confirm that drive A or drive C is properly identified. EKerryboorard The BIOS has detected a stuck key. Ensure that nothing is resting on the keyboard; if a key appears to be stuck, carefully pry it up. If the problem persists, you may need to replace the keyboard. EKBr/rIonrterface An error occurred with the keyboard connector. Ensure that nothing is resting on the keyboard; if a key appears to be stuck, carefully pry it up. If the problem persists, you may need to replace the keyboard. BNaos iRcOM The operating system cannot be located on drive A or drive C. Enter the system setup program and confirm that drive A or drive C is properly identified. Back to Contents Page Back to Contents Page System Setup Dell™ Dimension™ 1100/B110 Systems Service Manual Overview Entering System Setup System Setup Screens System Setup Options Boot Sequence Clearing Forgotten Passwords Overview Use system setup as follows: To change the system configuration information after you add, change, or remove any hardware in your computer To set or change a user-selectable option such as the user password To read the current amount of memory or set the type of hard drive installed Before you use system setup, it is recommended that you write down the system setup screen information for future reference. NOTICE: Unless you are an expert computer user, do not change the settings for this program. Certain changes can make your computer work incorrectly. Entering System Setup 1. Turn on (or restart) your computer. 2. When the blue DELL™ lo...