Assessments - 3, GPA: 4.3
(
)
)
|
por este dispositivo também tem outras instruções :
Notebooks - VGC-LM2S (1.46 mb)
Notebooks - VGC-LM2S (1.44 mb)
Notebooks - VGC-LM2S (1.46 mb)
Notebooks - VGC-LM2S (506.02 kb)
Facilidade de uso
n2233 NGetting Started Connecting a Power Source You need an AC adapter to connect to an AC power source and it must be plugged into the power source before you can establish communication with your wireless keyboard and mouse. . Use your computer only with the supplied AC adapter. 2424nNGetting Started To connect the AC adapter 1 Remove the back panel cover from the computer. See Removing and Replacing the Back Panel Cover (page 21) for the procedure. 2 Plug one end of the power cord (1) into the AC adapter (3). 3 Plug the other end of the power cord into an AC outlet (2). 4 Plug the cable connected to the AC adapter (3) into the DC IN port (4) on the computer. ! The shape of the DC In plug varies depending on the AC adapter. Replace the back panel cover. See Removing and Replacing the Back Panel Cover (page 21) for the procedure. 2525nNGetting Started . You can bundle the AC adapter cable along with other cables to keep them tidy. Snap open the cable clamp, route the cables through it, and then snap the cable clamp back shut as shown below: To disconnect your computer completely from AC power, unplug the AC adapter. Make sure that the AC outlets are easily accessible. ! If you unplug the AC adapter from your computer while the computer is on or in Sleep mode, you may lose all unsaved data. 2626nNGetting Started Connecting the Wireless Keyboard A wireless keyboard and four AA alkaline batteries for use in the keyboard are supplied with your computer. Before attempting to use the wireless keyboard, you must install the batteries and establish communication between the computer and the keyboard. . If you find your keyboard not working, for example after replacement of the keyboard batteries, try the following steps for reconnection. To connect the wireless keyboard ! To connect the wireless keyboard, it must be located within a range of 30 cm to 1 m from the computer. 1 Insert the supplied four AA batteries (1) into the battery compartment (2) on the bottom of the wireless keyboard. 2 Remove the back panel cover from the computer. See Removing and Replacing the Back Panel Cover (page 21) for the procedure. 3 Turn on the computer. 4 Slide the POWER switch (3) at the top of the keyboard to the ON position. 5 Press the CONNECT button (4) on the back of the computer. 6 Press the CONNECT button (5) on the bottom of the keyboard. The connect indicator turns on in the LCD window on the keyboard when connection is established between the computer and the keyboard. If not, repeat the procedure. ! Steps 5 and 6 must be completed within 10 seconds of each other. If the wireless keyboard is left unused for 20 minutes or longer, the connect indicator will turn off. This could indicate that the connection between your computer and the keyboard is lost. Press the Fn key to check that the connect indicator turns on before using the keyboard. 2727nNGetting Started Replace the back panel cover. See Removing and Replacing the Back Panel Cover (page 21) for the procedure. 2828nNGetting Started . You can check the battery indicator ( or ) in the LCD window on the wireless keyboard for its battery power level. If the wireless keyboard does not operate properly, the batteries may need to be replaced. If the wireless keyboard is not being used for an extended period of time, remove the batteries to avoid possible damage from battery leakage. If you want to put the wireless keyboard in a more 'ergonomic' position, flip open the keyboard feet. 2929nNGetting Started Connecting the Wireless Mouse A wireless mouse and two AA alkaline batteries for use in the mouse are supplied with your computer. Before attempting to use the wireless mouse, you must install the batteries and establish communication between your computer and the mouse. . If you find your mouse not working, for example after replacement of the mouse batteries, try the following steps for reconnection. To connect the wireless mouse ! To connect the wireless mouse, it must be located within a range of 30 cm to 1 m from the computer. Insert the supplied two AA batteries into the wireless mouse as shown below: 2 Remove the back panel cover from the computer. See Removing and Replacing the Back Panel Cover (page 21) for the procedure. 3 Turn on the computer. 3030nNGetting Started Slide the power switch on the bottom of the mouse to the ON position. Press the CONNECT button (1) on the back of the computer. Press the CONNECT button on the bottom of the mouse within 10 seconds from step 5. Communication between the mouse and the computer should now be established. 3131nNGetting Started Replace the back panel cover. See Removing and Replacing the Back Panel Cover (page 21) for the procedure. . If the wireless mouse does not operate properly, the batteries may need to be replaced. If the wireless mouse is not being used for an extended period of time, remove the batteries to avoid possible damage from battery leakage. 3232nNGetting Started Preparing for VESA Mounting Your computer ...
Este manual também é adequado para os modelos :Computadores - VGC-LM2E (5.12 mb)
Computadores - VGC-LM2ER (5.12 mb)
Computadores - VGC-LT2S (5.12 mb)
Computadores - VGC-LT2SR (5.12 mb)