Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Before You Begin
holes; the flange with round holes attaches to the
hand serial port labeled “Console”) to the serial port
SA7100/SA7120; that with the oval holes to the rack.
of any terminal. (A PC running Windows
This Quick Start Card is intended to guide you from initial
2.
Position the SA7100/SA7120 in the desired space of
HyperTerminal* is used here as an example.) Type
your 19” rack and attach the front flange of each
an appropriate name in the Name field of the
physical installation of the HP e-Commerce Server
mounting bracket to the rack with two screws each.
Connection Description window (e.g.,
Accelerator SA7100/SA7120 to an active command line
(Rack-mounting screws are not provided.)
“Configuration”), and then click the OK button. The
prompt (i.e., the “test” configuration). To proceed from the
Phone Number panel appears.
test configuration to production, refer to the HP e-Commerce
Free-Standing Installation
2.
In the Connect Using… field specify “COM1” (or the
Server Accelerator SA7100/SA7120 User Guide.
1.
Attach the provided self-adhesive rubber feet to the
serial port through which the PC is connected to the
Before you begin installation, you must:
SA7100/SA7120’s bottom.
SA7100/SA7120 if different from COM1).
3.
Click the OK button. The COM1 Properties panel
•
Determine the type of network cables you need
2.
Place the SA7100/SA7120 on a flat surface and make
sure that there is adequate airflow surrounding the unit
appears. Set the values displayed here to 9600, 8, none,
according to the following table:
(allow at least one inch of air space on all sides).
1, and none.
4.
Click the OK button.
SA7100/
SA7100/SA7120’s
Network Connections
SA7120’s
server
HyperTerminal* Paste Operations
network
connector
1.
Use the “Network Cable Requirements” table near
connector
If you’re using HyperTerminal* you must make the following
the beginning of this guide to select and install the
Workstation or
Crossover cable
Straight-through
the appropriate cables.
configuration change:
Server
cable
NOTE: Never connect both ports to the same network
1.
In the File menu, click Properties.
Switch or Hub
Straight-through
Crossover cable
segment (e.g., to the same hub or switch). Doing so creates
2.
Click the Settings tab.
cable
a feedback loop that adversely effects network bandwidth.
3.
Click the ASCII Setup button.
Router
Crossover cable
Not recommended
2.
Connect the provided power cable to the back of the unit.
4.
Change the values of Line and Character delay from 0 to
(There is no power switch.) Under normal circumstances,
at least 1 millisecond.
SA7100/
N/A
Straight-through
the SA7100/SA7120 requires approximately 30 seconds
5.
Click OK to exit ASCII Setup.
SA7120’s
cable
to boot. When the boot is complete, the unit’s Power LED
network
is steadily illuminated. (If the Power LED is not steadily
6.
Click OK to exit Connection Properties.
connector*
illuminated, please see Chapter 9, “Troubleshooting” in
the User Guide.)
Accessing the Command Prompt
SA7100/
Straight-through
N/A
SA7120’s server
cable
3.
If the Inline LED is neither steadily illuminated or blinking,
After the SA7100/SA7120 boots up, the password prompt
connector*
press the Bypass switch.
appears.
4.
At this point both the Network and Server LEDs should
* Applicable only to multiple, cascaded units.
be steadily illuminated. If not, please see Chapter 9,
NOTE: The password is not echoed on the command line.
“Troubleshooting” in the User Guide.
If you intend to install the SA7100/SA7120 in a rack, you will
1.
Type admin at the password prompt and press
also need:
Status Check
Enter to access the prompt:
•
Phillips screwdriver
Password: admin (password is not echoed at prompt)
Before proceeding to the Admin Terminal Connection
Current date: 2000 08/28 05:01
•
Rack-mounting screws (not provided)
section, take a moment to verify that the SA7100/SA7120 is
HP SA7120>
Physical Installation
correctly connected.
You are now ready for operations at the Command Line
Network and Server LEDs
Interface (CLI) of the SA7100/SA7120. A typical way to
WARNING: Do not remove the cover. There are no user-
begin would be as follows:
servicable parts inside.
Verify that the Network and Server LEDs are both
1.
Optionally, change your password from admin to
The SA7100/SA7120 is physically installed in either of two
illuminated. If one or both are not, refer to Chapter 9,
another password. Use the password command.
ways:
“Troubleshooting” in the User Guide.
HP SA7120> password
•
In a standard 19” rack, cantilevered from the provided
Inline LED
2.
Use set date to correct the date/time, if necessary.
mounting brackets
The date and time affect the validity of the certificate.
•
Free-standing on a flat surface with sufficient space for
A blinking Inline LED indicates that the system is online in
HP SA7120> set date
air-flow
Fail-safe mode. Refer to Chapter 9, “Troubleshooting,” or
Appendix B, for details on Fail-safe and Fail-through modes.
3.
Use the help command to list available commands (or
Rack Installation
refer to the Command Reference in Chapter 5 of the
Admin Terminal Connection
User Guide).
Rack mounting requires the use of the mounting brackets
HP SA7120> help
and all four of the included Phillips screws.
Run HyperTerminal* or a similar terminal emulator on your
4.
Perform key/certificate setup. (See Chapter 3 of the User
1.
Attach a mounting bracket to each side of the SA7100/
PC. The steps below are illustrative of HyperTerminal*.
Guide for details.)
SA7120, using two of the provided screws for each
Other terminals will require different procedures.
bracket. Use the holes near the front of the SA7100/
SA7120’s sides. The brackets have both round and oval
1.
Use the serial cable provided with the SA7100/
SA7120 to connect the device’s serial port (the left-