Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Eject button Floppy drive power cable Floppy drive Red stripe to match signal cable Pin 1 on the connector 4. Secure the drive cage with a screw. Chapter 2: Hardware setup 2.10.6 Front I/O board You need to remove the front panel assembly before you can remove the front I/O board. Refer to section “2.5.1 Removing the front panel assembly” for instructions. To remove the front I/O board: 1. Remove the screw that secures the front I/O board bracket to the front panel. 2. Carefully pull out the bracket until you see the cables connected to the I/O board. 3. Disconnect all the cables from the I/O board. 4. Remove the screw that secures the I/O board to the bracket. ASUS AP1720-E1 barebone server To install the front I/O board: 1. Place the I/O board in the bracket, component side up. Secure the front I/O board to the bracket with a screw. 2. Position the I/O board into the bay with the component side to the left (close to the HDDs). Connect the I/O cables to the connectors on the back of the I/O board. 3. Insert the I/O board into the bay until the bracket fits the front edge of the bay. 4. Secure the I/O board bracket with a screw. USB 2.0 connector Chapter 2: Hardware setup 2.10.7 Chassis footpads and roller wheels The barebone server system is shipped with four footpads attached to the bottom of the chassis for stability. You need to remove these footpads if: • if you want to replace the footpads with the bundled roller wheels • you wish to install the system to a rack (Refer to “Chapter 3 Installation options” of this user guide, and to the “Rackmount Kit” user guide for instructions) To remove the footpads: 1. Lay the system chassis on its side. 2. Use a flat screwdriver to flip out the top layer of a footpad. 3. Remove the footpad by rotating it counterclockwise. 4. Repeat steps 2 and 3 to remove the other three footpads. ASUS AP1720-E1 barebone server For convenient transport, install the roller wheels the came with the system package. Each wheel has a brake lock to stabilize the chassis in place. To install the chassis wheels: 1. Lay the chassis in its side. 2. Locate the designated screw holes for each of the four wheel sets. Take note of the numbers alongside each hole when placing screws. 3 1 2 4 3. Secure each wheel to the bottom of the chassis using four screws. 4. Repeat steps 2 and 3 to install the other three wheels. Remove the chassis roller wheels if you wish to mount the system to a rack. To remove the chassis wheels: 1. Lay the system chassis on its side. 2. Use a Phillips screwdriver to remove the screws that secure the wheels to the bottom of the chassis. 3. Repeat step 2 to remove the other three roller wheels. Chapter 2: Hardware setup Chapter 3 Chapter 3 This chapter describes how to install optional components into the barebone server and create your desired configuration. Installation options ASUS AP130-E1 barebone server The items required for the optional configurations described in this chapter are not included in the standard barebone system package. These items are purchased separately. Mounting the system to a rack Remove the footpads or roller wheels Refer to section “2.10.7 Chassis roller wheels and footpads” for instructions on removing the footpads or roller wheels. Remove the top cover To remove the top cover: 1. Remove the side cover. Refer to section “2.1.1 Removing the side cover” for instructions. 2. Remove the front panel assembly. Refer to section “2.5.1 Removing the front panel assembly” for instructions. 3. Locate the lock tab underneath the top cover and press it outward to release the cover. 4. Slide the top cover toward the front panel, then lift it up from the chassis. Lock tab of top cover (bottom view) Attach the rack rails Refer to the installation guide that came with the Rackmount Rail Kit for instructions on how to attach the rails and on the barebone server system and the corresponding rails on the industrial rack. Chapter 3: Installation options Appendix Appendix This appendix gives information on the power supply that came with the barebone server. Power supply ASUS AP130-E1 barebone server A.1 General description The server comes with a 350W ATX power supply with universal AC input that includes PFC and ATX-compliant output cables and connectors. The power supply has nine plugs labeled P1 to P10 (no P3). Take note of the devices to which you should connect the plugs. P6 P5 P4 P7 P8 P9 P10 P11 P12 PS1 PS2 PS3 PS1 Motherboard 20-pin ATX power connector PS2 Auxilliary power connector PS3 Motherboard 4-pin +12V AUX power connector P4 SATA backplane P5 Peripheral device (available) P6 Peripheral device (available) P7 Peripheral device (optical drive) P8 Peripheral device (available) P9 Peripheral device (available) P10 SATA backplane P11 Peripheral device (available) P12 Floppy disk drive Chapter 3: Installation options A.2 Specifications Input Characteristics Input Voltage Range 90Vac to 135 Vac /180 Vac to 265 Vac, auto-range, single phase Normal Voltage ...