Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
When you install a server blade in the basic unit, an important factor is the height. Figure 28 shows a 2-way server blade, which occupies one slot in the basic unit. Figure 28: PRIMERGY BX620 S3/S4 2-way server blade PRIMERGY BX600 S2 Basic Unit Server Blades The 4-way server blade is twice the height and occupies two slots (figure 29). Figure 29: PRIMERGY BX630 scalable server blade (4-way configuration PRIMERGY BX600 S2 Basic Unit Server Blades Installation Sequence 7.1 Installation Sequence On the front of the PRIMERGY BX600 S2 basic unit are ten slots for server blades (numbered 1 - 10 from left to right). 1 2 3 4 5 6 7 8 9 10 Figure 30: BX600 S2 basic unit with ten 2-way server blades All ten slots are connected to the infrastructure modules on the back of the BX600 S2 basic unit via the midplane of the BX600 S2 basic unit: – Switch blade(s) – Fibre Channel pass-thru blade(s) (optional) – Ethernet pass-thru blade(s) (optional) – Management blade(s) – KVM blade – Power supply units T CAUTION! PRIMERGY BX620 S4 server blades are not for use in slots 4 an 10 of the PRIMERGY BX600 S2 basic unit. In a PRIMERGY BX600 S2 basic unit different models and configurations of server blades can be operated alongside each other. PRIMERGY BX600 S2 Basic Unit Installation Sequence Server Blades The order in which the server blade slots are filled depends on whether you are using 2-way server blades or 4-way server blades or a mix of the two, and how the server blades are equipped. Configuration Diagram for 2-way Server Blades – Slot 4 is filled first. – Next, slots 5 through 10 are filled in numerical order, followed by slots 1 through 3. – 2-way server blades with SCSI controller in a PCI extension module can only be installed in slots 5 and 6 because of the cabling arrangement in the rack (see section “Cable Routing” on page 43). 1 2 3 4 5 6 7 8 9 10 8 9 10 1 2 3 4 5 6 7 Figure 31: Installation sequence for 2-way server blades PRIMERGY BX600 S2 Basic Unit Server Blades Installation Sequence Configuration Diagram for 4-way Server Blades – Slots 3 and 4 are filled first. – Next, slots 5 through 10 are filled in pairs in numerical order, followed by slots 1 and 2. 1 2 3 4 5 6 7 8 9 10 5 1 2 3 4 Figure 32: Installation sequence for 4-way server blades Configuration Diagram for a Mix of 2-way and 4-way Server Blades – The 4-way server blades are fitted first, followed by the 4-way server blades – Begin with a 4-way server blade in slots 3 and 4. 1 2 3 4 5 6 7 8 9 10 6 Dummy server blade1 2 3 4 5 Figure 33: Installation sequence for three 2-way and three 4-way server blades G 2-way server blades with SCSI controller can only be fitted in slots 5 and 6. If only one 2-way server blade with SCSI controller is to be fitted, it must go in slot 5, with a dummy server blade in slot 6. PRIMERGY BX600 S2 Basic Unit Adding a Server Blade to the System Server Blades Configuration Diagram for a Mix of an 8-way Server Blade with 4-way and 2-way Server Blades Begin with the 8-way server blade in slots 1-4, followed by the 4-way Server- Blades and the 2-way Server-Blades. I Server blades with SCSI controller can only be fitted in slots 5 and 6. 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 Figure 34: Installation sequence for an 8-way, two 4-way and two 2-way server blades 7.2 Adding a Server Blade to the Basic Unit Depending on the desired configuration, the system can be upgraded with up to 10 server blades. T CAUTION! . Read the safety information and the information on handling electrostatic- sensitive components in the section “Components With Electrostatic-Sensitive Devices” on page 25. . Energiegefahr - neu. Removing the Dummy Module All unoccupied slots in the basic unit are fitted with dummy modules to ensure that the electromagnetic emission properties of the system are observed and that the system components are properly cooled. PRIMERGY BX600 S2 Basic Unit Server Blades Adding a Server Blade to the System If you want to add a server blade, you must first remove the dummy module from the corresponding slot. Figure 35: Removing a server blade dummy module — Release the locking mechanism of the ejecting handles by pressing the touch points on the inside of both handles (1) simultaneously. The ejecting handles of the dummy module will be disengaged. — Swing up the upper handle and swing down the lower handle simultaneously (2) until the locking mechanism of the dummy module disengages and the dummy module ejects. — Remove the dummy module completely from the slot (3). T CAUTION! Keep the dummy module for future use. If the server blade is removed and not replaced with a new server blade, then the dummy module must be reinstalled for cooling, to comply with the applicable EMC regulations (regulations on electromagnetic compatibility) and for fire protection. PRIMERGY BX600 S2 Basic Unit Adding a Server Blade to the System Server Blades Installation is the same as for the server blade (see “Inserting the Server Blade” on page 78). Inserting the...
Este manual também é adequado para os modelos :Computadores - PRIMERGY BX600 S2 (3.56 mb)