Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
Follow these steps to install the mounting rails: Extend the component rail (a) from the mounting rail (b) until the component rail release latch clicks. Hold down the latch and slip the component rail out of the mounting rail. Do the same thing to the other mounting rail. Note: Each mounting rail consists of a fixed outer piece that screws onto the mounting bracket and an inner sliding piece controlled by a steel ball gearing movement. This inner sliding piece is not detachable. 2 Put the component rails aside. 3 Attach the mounting brackets to the mounting rails. The mounting brackets consist of two metal bars to be attached on both ends of the mounting rails. f Unlock the inner sliding rail using your finger. g Push it forward. 134 Appendix B: System rack installation guide h Slide the roller towards the lock. i Adjust the inner sliding rail until you can see the screw holes. j Attach the mounting bracket to the front end of the mounting rail and align the screw holes. Secure it with two M4 x L8 screws with nut and washer. k Slide and adjust the inner sliding rail again to see the third screw hole. Secure it with one M4 x L8 screw with nut and washer. The position of the mounting bracket on this end is fixed. l Extend the inner sliding piece of the mounting rail until you can see the screw holes on the other end. Attach the mounting bracket with two M4 x L8 screws with nut and washer. The mounting rail on this end is adjustable. Install the left mounting bracket first using four M6 screws with locating rings. 136 Appendix B: System rack installation guide 5 Install the right mounting bracket using four M6 screws with locating ring. 6 Secure the front side of the bracket first and then secure the rear end with one M6 screw with locating ring. 7 Attach the cable carrier to the rack, overlapping the mounting bracket, with two M6 screws without locating rings. Install a cage nut on the topmost square hole to hold the screw. Note: The cable carrier allows you to tie-wrap all cables to and from the server. As you slide the server in and out of the rack, the cable carrier collapses and extends, keeping the cables untangled and attached to the server. Attach the handle to the tray using two M5 metal screws. Attach a component rail on each side of the tray with ten M4 metal screws. Appendix B: System rack installation guide 10 Install the server on the tray. a Check the stand-off brackets that came with your server’s rackmount kit. Each stand-off bracket is marked as follows: Rear left Rear right Front left Front right b Attach the stand-off brackets to the tray using eight M5 metal screws. 139 c Remove the front panel door of the server. Refer to “Removing the front panel door” on page 37 for instructions. d Remove the stands from the server. Keep the screws for later use. 140 Appendix B: System rack installation guide e Place the server on the tray and secure it with the four screws removed from the stands. 141 11 Extend the inner sliding piece of each mounting rail forward until it clicks. 12 Carefully align the tray's rail with the mounting bracket's rail, and then push the server into the rack until it clicks. 13 Depress the component rail release latch on either side of the server and then slide the server into the rack. 142 Appendix B: System rack installation guide Note: To avoid personal injury, care should be taken when pressing the component rail release latches and sliding the component into the rack. 14 Remove the two screws on the upper edge of the server and then cut the clip that holds the handle to completely depress the handle. 15 Attach the rack server cover to the server using the thumbscrews. 143 16 Attach the other end of the cable carrier to the tray using two M5 metal screws. 17 Extend the cable carrier to bundle all the cables to it using the cable clamps. Route all cables from the cable carrier to the cable management bracket located on the rear of the rack. 144 Appendix B: System rack installation guide Note: For details on cabling and cable management brackets installation, refer to the documentation that came with your system rack . 18 Install two cage nuts for the upper left and right thumbscrews. (The lower left and right thumbscrews do not need cage nuts.) Secure the server to the rack using the thumbscrews. Note: Refer to the documentation that came with your system rack for instructions on how to install cage nuts. Index A Advanced Desktop Agent System Requirements 111 Advanced Server Agent System Requirements 111 Advanced System Manager (ASM) System Requirements 111 ASM Console installation 112 ASM Server Agent configuring SCO Openserver Agent 115 installing Microsoft Windows NT Agent 116 installing Novell Netware Agent 112 installing SCO Openserver Agent 114 installing SCO Unixware Agent 115 B basic connections 22 keyboard 22 monitor 24 mouse 23 network 24 power cable 25 BIOS Setup utility 69 Abort Settings Change 106 Advanced Options 100 Boot Options 86 Date and Time 89 Disk D...