Assessments - 5, GPA: 4 ( )

Fabricante : Kenmore Arquivo Tamanho: 1.84 mb Arquivo Nome : 442995b7-57ff-4da5-849f-85afb22cd960.pdf Língua de Ensino:

8°C Heating: . 14°C NON SERVICEABLE CRITERIAS TURN OFF POWER SUPPLY then please consult authorized dealer under the following conditions: • Abnormal noise during operation. • Water/foreign particles have entered the remote control. • Water leaks from Indoor unit. • Circuit breaker switches off frequently. • Power cord becomes unnaturally warm. • Switches or buttons are not functioning properly. FOR EXTENDED NON-USE • Activate Heat mode for 2~3 hours to remove moisture left in the internal parts thoroughly to prevent mould growth. • Turn off the power supply. • Remove the remote control batteries. ALUMINIUM FIN • Clean the fi lters regularly. • Wash/rinse the fi lters gently with water to avoid damage to the fi lter surface. • Dry the fi lters thoroughly under the shade, away from fi re or direct sunlight. • Replace any damage fi lter. e-ion FILTERS Clean with dry cotton bud. • Active e-ion generator cleaning is recommended every 6 months. ACTIVE e-ion GENERATOR WASHING INSTRUCTIONS e-ion CHARGING WIRE INDOOR UNIT Wipe the unit gently with a soft, dry cloth. Remove Front Panel • Raise and pull to remove the front panel. • Wash gently and dry. Close Front Panel • Press down both ends of the front panel to close it securely. FRONT PANEL TTRROOUUBBLLEESSHHOOOOTTIINNGG SymptomSymptom CauseCause Mist emerges from indoor unit. • Condensation effect due to cooling process. Water flowing sound during operation. • Refrigerant flow inside the unit. The room has a peculiar odour. • This may due to damp smell emitted by the wall, carpet, furniture or clothing. Indoor fan stops occasionally during automaticfan speed setting. • This helps to remove the surrounding odours. Airflow continues even after operation hasstopped. • Extraction of remaining heat from the indoor unit (maximum 30 seconds). Operation is delayed a few minutes after restart. • The delay is a protection to the unit’s compressor. Outdoor unit emits water/steam. • Condensation or evaporation occurs on pipes. Timer indicator is always on. • The timer setting repeats daily once set. Power indicator blinks during operation, theindoor fan is stopped and vane is closed. • The unit is in defrost mode, and the melted frost is drained from the outdoor unit. Indoor fan stops occasionally during heatingoperation. • To avoid unintended cooling effect. Power indicator blinks before the unit is switched on. • This is a preliminary step in preparation for the operation when the ONtimer has been set. Cracking sound during operation. • Changes of temperature cause the expansion/contraction of the unit. The following symptoms do not indicate malfunction.The following symptoms do not indicate malfunction. SymptomSymptom CheckCheck Heating/Cooling operation is not workingefficiently. • Set the temperature correctly. • Close all doors and windows. • Clean or replace the filters. • Clear any obstruction at the air inlet and air outlet vents. Noisy during operation. • Check if the unit has been installed at an incline. • Close the front panel properly. Remote control does not work. (Display is dim or transmission signal is weak.) • Insert the batteries correctly. • Replace weak batteries. The unit does not work. • Check if the circuit breaker is tripped. • Check if timers have been set. The unit does not receive the signal from theremote control. • Make sure the receiver not obstructed. • Certain fluorescent lights may interfere with signal transmitter. Please consult your nearest dealer. PATROL operation does not work. • Press and hold for 15 seconds until beep sound is heard, press again. Patrol sensor indicator on the indoor unit is blinking. • Press twice. If the patrol sensor indicator still blinking, pleaseconsult authorized dealer. Check the following before calling for servicing.Check the following before calling for servicing. The unit stops and the timer indicator blinks.The unit stops and the timer indicator blinks. Use remote control to retrieve error code. 1 Press for 5 seconds. 3 Press for 5 seconds to quitchecking. 2 Press until you hearbeep sound, then jotdown the error code. 4 Turn the unit off and reveal the error code to authorized dealer. Note: • For certain error, you mayrestart the unit with limited operation with 4 beepsduring operation starts. TROUBLESHOOTINGTROUBLESHOOTING SymptomSymptom CauseCause Mist emerges from indoor unit. • Condensation effect due to cooling process. Water flowing sound during operation. • Refrigerant flow inside the unit. The room has a peculiar odour. • This may due to damp smell emitted by the wall, carpet, furniture or clothing. Indoor fan stops occasionally during automaticfan speed setting. • This helps to remove the surrounding odours. Airflow continues even after operation hasstopped. • Extraction of remaining heat from the indoor unit (maximum 30 seconds). Operation is delayed a few minutes after restart. • The delay is a protection to the unit’s compressor. Outdoor unit emits water/steam. • Condensation or evaporation o...

Baixe o seu

Para fazer o download, introduza 2 dígitos :