Assessments - 4, GPA: 3
(
)
)
|
Facilidade de uso
Peel off the backing and attach the FOAM SEAL as shown in Fig 5, Upperguide ITEME L _Open the window Mart{ a line on center of the window inner sill. Carefully place the cabinet on the window inner sill and align the center of the cabinet front with the center tine marked in the window inner silt. : _Window sill FIG. 7 _Pull the bottom window sash down behind the upper guide until they meet. NOTE: Do not pull the window sash down so tightly that the movement of side curtain is restricted,, Window sash Upper guide Foam seal" Side curtain _ Loosety assemble the sill supports using the parts in FIG. 9. FIG. 5 ,.ooo, o. oo _ Insert the side curtain (iTEM A) into the upper guide and lower guide of the air conditioner,,Fasten the curtains to the unit with screws (ITEM E) "_ f/'_-- u ITEMC '" ITEMg _TEMD FIG. 9 Q Select the position that wilt place the sill supports _] Attach the L BRACKET (ITEM J) with screw near the outermost point on sill (FIGo10) (ITEM G).,(FIG, 14) Attach the sill supports to the cabinet track hole / ]II ,TEM closest to the selected position using screw (ITEM E). Lower guide , ,, _._, _& _ FIGo 14 ' / 'N CaNnel _] DRAINAGE Be sure to insertthe drain pipe into base pan before installation., The air conditioner must be installed with a slight tilt _ Place the sill supports with the cabinet on the downward to the outside for proper water drainage° window sill's selected position The air conditioner will drain the excess condensed _ti] The cabinet should be installed with a very water through the drain pipe (FIG, I5) slight tilt (about 1/4") downward toward the outside (FIG 11),, DRAINp_BASE PAN REAR Adjust the bolts and the nuts of sill supports to level the cabinet., '-'-In.,,_ BASE PAN BOTTOM FIG. 15 _ Slide the chassis into the cabinet. (FIG. 16) J _ _------fo CAUTION: For security purposes, reinstall side TEMB FIG. 11 screws you removed in step I. [_r _ Attach the cabinet to the inner sill by driving the screws (_TEM F) through the front angle into the window inner sill (FIG, 12),, i I:I Ir Screw "_,,_ FIGo16 Screw _Cut the foam strip (ITEM H) to the proper length and insert between the upper window sash and the lower window sash,, (FIG, 17) . --Lower Guide I_ tTEM F ITEMB FIG. 12 []Pull each side curtain fully to each side of FIGo17 window opening Attach each side curtain to the window sash using screws (ITEM G). (FIG, 13) _The vent control handle must be straightened before the decorative front is attached Putl out part @ to align with part (_. ITEM G .Part( FIG. 13 FIG. t8 -7_ _ FRONT INSTALLATION Install the front grille(packed separately) onto the cabinet as follows: • Hook upper tabs of front grille into slots on the cabinet top° (FIG, 19) o Push front gritle's tips towards the cabinet in order to snap side tabs into the cabinet, (FIG,,19) • Open the inlet grille.,(FIG, 20) • installthe screw (ITEM E) through the front grille. (FIGo20) oCtese inlet grille. (FIG.,21) Front lnstaflation FIG, 19 Front Installation _.t Front installation FIG. 21 _IF AIR CONDITIONER IS BLOCKED BY STORM WINDOW FRAME , If storm windowpresents interference, fasten a 2'* wide wood strip to the inner window sill across the full width of the sill The wood strip should be thick enough to raise the height of the window silt so that the unit can be installedwithout interference fromthe the storm window frame. See FfG 22 Top of wood strip should be approximately 3/4" higher than the storm window frame to help condensation to drain properly to the outside • Install a second wood strip (approximately 6" long by 1V2"wide and same thicknessas first strip) inthe center of the outer sill flush against the back of the inner sill Screw the L brackets into thisstrip This will raise the L bracket as shown in F1G 22, 1 1/2" min WOOD STRIP MOUNTED (38ram) ON TOP OF INNER S_LL __ --_-3/4" _L, CLEARANCE V J" ] 4 _ _ WINDOW INNER ]L BRACKET I FRAME J J OUTER l IS LL INSIDE 1 OUTSIDE FIG, 22 REMOVAL FROM WINDOW • Turnoff and unplugtheair conditioner . Removethefrontgrille,SeeHOWTOREMOVETHE FRONTGRILLE Referto page 13 . Unscrewthe sidescrewsthatyou installedinStep 15 • Slidethe air conditionerout efthecabinet, BECAREFULNOTTODROPIT,Heldontoit firmlythe whole way slidingit out Once removed,set it safety out of the way -RemovetheL bracketfromwindowframeand the sash seal from betweenthe windows • Unscrewthe sidecurtainsfromthe windowframe Fold thembackto thesides of the cabinet =Removescrewsattachingcabinettoinnersill Becareful notte totcabinetfalloncescrewsareremoved • Removecabinetfrom windowopening, • Place air conditionerinto cabinet Reinstallside screws and Front Grille • Place unit and all assemblyhardwarein air conditioner shippingcarton, and storeinclean,dry place ° Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit • When handling the air conditioner, be carefu...