Assessments - , GPA: ( )

Instruções de Operação Denso, Modelo OFFICE PRO 36

Fabricante : Denso
Arquivo Tamanho: 1.34 mb
Arquivo Nome : b316be52-5008-46ef-a981-2e799cb233e3.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

• The Office Pro 36 is equipped with a six (6) foot (1.8 meter) AFCI power cord. If replacement, fixed location (hard wired) or power cord lengthening (extension cord) cords are required, contact your reseller or a qualified licensed electrician for approved replacement methods. • Never fold, or place heavy objects on the power cord. This could result in damage to the power cord causing electrical shock or fire. • Do not place water or any other liquid on the unit. This can cause damage to the unit and increase the risk of electrical shock. • Do not sit or stand on the unit. 1 INVENTORY After unpacking your MovinCool unit, please check to make sure you have the following items: • Office Pro 36 MovinCool Unit (1) • Operation Manual/Warranty Card (1) NOTE: If any of these items were not included in the box or appear damaged, please contact your MovinCool reseller for replacement. OPERATION MANUAL/ WARRANTY CARD 36 INSTALLATION Choosing an Installation Site .CAUTION: Following are some precautions to consider before choosing your installation site. Please review carefully as improper installation may result in personal injury or damage to the unit. • Do not use the unit in areas where leakage of flammable gas may occur. • Do not use the unit in areas where it will be exposed to rain or water. • Do not use the unit in an atmosphere of excessively corrosive gas or vapor. • Do not use in areas where the temperature is outside the allowable operating range. • Do not install the unit in sloping areas. The unit may move or topple over even if the casters are set to the LOCKED position. • Install the unit in areas that can withstand the weight of the unit. The Office Pro 36 weighs approximately 440 lbs (200 kg). • Allow 24 inches (610 mm) of unobstructed airflow for both air inlets and outlets. • Do not use the unit above the following conditions: 95. F (35 .C) 2 Moving the Unit Unlock the casters and push the MovinCool unit, using the side handles, to a flat, level surface and set the casters back to the LOCKED position. UNLOCKED LOCKED FRONT AND BACK HANDLES Plugging in the Unit • Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe off with a clean, dry cloth. • Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. • Fully insert plug into the A/C outlet. .WARNING: • If the power cord or plug is damaged, repair should only be performed by qualified electrical personnel. • Do not connect/disconnect the power cord or attempt to operate buttons with wet hands. This could result in electrical shock. .CAUTION: The AC outlet (208/230 VAC Single Phase, 60Hz) needs to be rated at 30A or higher. Do not share the outlet with any other instrument or equipment. NOTE: • Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign matter. • The Office Pro 36 model is equipped with an approved NEMA plug configuration (6-30). The appropriate outlet must be used for this plug type. 3 FEATURES OP36 Features • An electronic control panel which allows the user to control the unit’s operation easily. • Dual fan speeds (either High or Low) in both COOL and Fan Only modes. • A digital display that indicates the Temperature SET POINT (either Fahrenheit or Celsius) in which the COOL Mode will operate. This is also the temperature the unit will try to maintain. The Temperature SET POINT can be adjusted by the SET TEMP buttons (Ў/^). (65.F-95.F) • A condensate drain TANK FULL indicator display (LED). • An automatic restart feature when the power is lost and regained. The unit will return to the operating mode it was in prior to the loss of power. Any preset program will be retained in the memory in the event power loss occurs. • A programmable Clock/Timer function. This allows the user to program a specific time of day that the unit will begin to operate/start and turn off/end. • A 2-digit room temperature display. • Two condensate tanks with condensate float OPERATION Control Panel Before operating the unit, it is important to familiarize yourself with the basic controls located on the control panel. 1. COOL ON/OFF Button - Activates/deactivates the COOL mode/turns the unit off. 2. FAN ON/OFF Buttons - Activates/deactivates the HIGH or LOW fan mode. 3. SET TEMP Buttons (Ў/^) -Increases/decreases the temperature set point. 4. 4.4. T TTTANK FULL LED - Flashes when the drain tank is full. 5. SET POINT Display - Indicates the current temperature set point; also used to display clock hour when programming. 6. ROOM TEMP Display - Indicates the current room temperature; also used to display the clock minutes when programming. 4 SET TEMP CLOCK/TIMER FAN ON/OFF COOL ON/OFF PROGRAM Office Pro 36 SET START TIME END TIME SET CLOCK RUN HRS MIN 1211910SET TEMP CLOCK/TIMER FAN ON/OFF COOL ON/OFF PROGRAM Office Pro 36 SET START TIME END TIME SET CLOCK RUN HRS MIN 1211910 8 7. Temperature Scale...