Assessments - 3, GPA: 3.3 ( )

Fabricante : Frigidaire Arquivo Tamanho: 1.83 mb Arquivo Nome : Língua de Ensino:

In the event that the power supply cord is damaged, it cannot be repaired-it must be replaced with a cord from the Product Manufacturer. Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord. Grounding type wall receptacle Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power supply cord with 3-prong grounding plug and current detection device Read all instructions before using this air conditioner. For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings. Prevent Accidents To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following: • Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille. • If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first. If the window is a triple-track type with a screen panel included, remove the screen completely before installation. • Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual. Save this manual and the installation instructions for possible future use in removing or reinstalling this unit. • When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. Electrical Information The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements. • Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. • Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. • Do not run air conditioner with outside protective cover in place. This could result in mechanical damage within the air conditioner. • Do not use an extension cord or an adapter plug. READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER. Operation of Current Device Plug in & press RESET NOTE: Some plugs have buttons on the top. The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: 1. Plug in the Air Conditioner. 2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out. 3. Press the RESET button. Again you will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head). NOTES: • Do not use this device to turn the unit on or off. • Always make sure the RESET button is pushed in for correct operation. • The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. • If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer. 4 5 Auto Temp ON/OFF LIGHT REMOTE CONTROL ACTIVATES TIMER FAN SPEED SETS MODE ADJUSTS TEMP & TIME Air Conditioner Features UNIT CONTROL ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control alone or with the remote. Battery Size: AAA Warning: do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. TO TURN UNIT ON: NOTE: The following instructions represent the Unit Controls, the same instructions can be used for the Remote Control. DO THIS: PRESS ON/OFF BUTTON YOU WILL SEE: YOU WILL SEE: Note: Tap or hold either up( ) or down( ) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 60.F (16.C) and 90.F (32.C). If you want the display to read the actual room temperature. See “To Operate on Fan Only” section on Page 6. TO CHANGE TEMPERATURE SETTING: PRESS TO RAISE PRESS TO LOWER DO THIS: AUTO TEMP SETS DISPLAYS TEMPERATURE/TIME FAN SPEED ACTIVATES TIMER CHECK FILTER RESET BUTTON SETS MODE TURNS UNIT ON OR OFF AUTO TEMP FEATURE SLEEP MODE SETS FAN SPEED ADJUSTS TEMP & TIME 6 Air Conditioner Features (c...

Baixe o seu

Para fazer o download, introduza 2 dígitos :