Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
See Fig. 5. • Expand the shutter frames (fully) on each side and secure the top of the frames to the window sash using one 3/4"(19mm)screw on each side and one in the “L” shaped mounting bracket. See Fig. 5 • Secure the shutter clamp on each side of the (lower) shutter and secure to window sill using one 3/4"(19mm)screw on each side. Fig.5 • Place the second foam sealing strip to fit the opening between the inside and outside windows then attach the safety lock to the outside window frame using one 3/4”(19mm) scre w. See Fig. 6. PLEASE NOTE: Window applications come in a variety of different styles. Therefore, it may be necessary to modify or improvise your particular installation. 3/8"(10mm) Screw “L” Shaped Mounting Bracket “U” Shaped Channel Fig. 3 (Factory Installed) Fig. 5 “L” Shaped Mounting Bracket Window Sash Fig. 6 Foam Seal Shutter clamps Safety Lock 3/4"(19mm) Screws 3/4"(19mm) Screw Shutter Frame Shutter Fig. 4 Shutter Tabs sbat otni nwod edilS " " " " " " " " 7 Operating Instructions SELECTOR SWITCH The selector switch controls fan speed and/or cooling speed. To set desired cooling temperature, simply rotate the SELECTOR knob to the appropriate setting. FAN SPEEDS LOW FAN will circulate air at minimum speed without cooling. MED FAN will circulate air at medium speed without cooling. COOLING MODES LOW COOL provides cooling with minimum air circulation. Recommended for night-time use. HIGHCOOL provides cooling with maximum air circulation. Recommended for quick cooling or for extremely hot days. Once room is cooled, reduce setting to LOW COOL. OFF shuts-down the unit completely. NOTE: Always allow 3 minutes before switching from one mode to another. THERMOSTTA The thermostat automatically controls the (compressor) cooling cycle and maintains the selected room temperature .To set the thermostat, rotate the thermostat knob to the desired cooling setting (1 warmest ~ 7 coldest). The fan motor will continue to operate after the compressor (cooling) has cycled o ff.This is normal. • HIGHFAN " "will circulate air at maximum speed without cooling. • • • • Selector Switch Thermostat CAUTION When using FAN control, turn selector switch slowly allowing unit to adjust. When using THERMOSTAT, be sure to allow three minutes before changing temperature . Adjusting too quickly may cause compresspr to overload. 1 2 3 4 5 6 7 ARRET OFF TEMP. MED COOL" " provides cooling with medium air circulation. Recommended for night-time use. • Care and Maintenance When cleaning the air conditioner, be sure to turn the SELECTOR knob to the “OFF” position and disconnect the power cord from the electrical outlet. 1. DO NOT use gasoline, benzine, thinner or other chemicals on the air conditioner as these substances may cause damage to the paint finish and deformation of plastic parts. 2. Never attempt to pour water directly on unit as this will cause deterioration of the electrical insulation. Air Filter Information If the air filter becomes clogged with dust, air flow is obstructed and reduces efficiency. The air filter should be cleaned every 2 weeks. Air Filter Removal: The air filter is located behind the air intake front grill. To remove the air filter, grasp the sides of the front grill and pull forward to open and access the filter. To reinstall the air filter, reverse the above procedures. The air filter may be vacuumed or washed by-hand in warm water. Dry thoroughly before installing. Cleaning Air Filter 1. Use a vacuum cleaner with soft brush attachment. 2. Wash the filter in lukewarm water below 40°C (104°F): To get better results, wash with soapy water or a neutral cleaning agent. 3. Rinse the filter with clean water and dry thoroughly before re-installing. IMPORTANT DO NOT forget to install the air filter. If the air conditioner is left to operate without the air filter, dust is not removed from the room air and may result in machine failure. When the air inlet grill and cabinet are dirty, wipe with lukewarm water (below 40°C). Use of a mild detergent is recommended. End-of-Season Care 1. Operate the fan alone for half a day to dry out the inside of the unit. 2. Turn off power and remove plug from wall socket. 3. Clean filter. 4. Store (covered) air conditioner in a dry location. CAUTION When installing and/or removing the air conditionner from the window, ensure that caution is taken to prevent the from failing backward. It is recommended that installtion or removal of the airconditioner is done with assitance to prevent injury to persons or damage to the unit or property. 8 Trouble shooting Guide Frequently, a problem is minor and a service call may not be necessary, use this trouble shooting guide for a possible solution. If the unit continues to operate improperly, call Danby’s Toll Free Number 1-800-263-2629 for assistance, or call one of our service depots listed in the enclosed “Authorized Service Depot” listing provided with this unit. Difficulty Air conditioner will not operate. Inefficient or no cooling. N...