Assessments - 4, GPA: 3.8 ( )

Fabricante : Bard Arquivo Tamanho: 280.08 kb Arquivo Nome : Língua de Ensino:

Manual 2100-351 Page 2 Manual 2100-351 Page 3 FIGURE 1 UNIT DIMENSIONS WL602N, WL6023, WL4823 ONLY MIS-1451 Manual 2100-351 Page 4 FIGURE 2 UNIT DIMENSIONS WL6022, WL4822 ONLY MIS-1452 TABLE 2 ELECTRICAL SPECIFICATIONS Manual 2100-351 Page 5 Mode l SINGL E CIRCUI T DUA L CIRCUI T Rate d Volts & Phas e No . Fiel d Powe r Circuit s • Minimu m Circui t Ampacit y • Maximu m Externa l Fus e o r Ckt . Breake r • Fiel d Powe r Wir e Siz e • Groun d Wir e Siz e • Minimu m Circui t Ampacit y • Maximu m Externa l Fus e o r BreakerCkt . • Fiel d Powe r Wir e Siz Groun d Wir Siz CK T A CK T B CK T A CK T B CK T A CK T B CK T A CK T B WL4822A00 , A0 Z 230/208- 1 1 3 8 5 0 8 1 0 N/ A N/ A N/ A N/ A N/ A N/ N/ N/ WL4822B00 , B0 Z 230/208- 3 1 2 6 3 5 8 1 0 N/ A N/ A N/ A N/ A N/ A N/ N/ N/ WL4823A00 , A0 Z 230/208- 1 1 3 8 5 0 8 1 0 N/ A N/ A N/ A N/ A N/ A N/ N/ N/ WL4823B00 , B0 Z 230/208- 3 1 2 6 3 5 8 1 0 N/ A N/ A N/ A N/ A N/ A N/ N/ N/ WL6022A00 , A0 Z A0 5 A1 0 230/208- 1 1 1 1 4 4 4 4 5 5 6 0 6 0 6 0 8 8 6 1 0 1 0 1 0 N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ N/ N/ N/ N/ N/ N/ N/ N/ WL6022B00 , B0 Z B0 9 230/208- 3 1 1 3 2 3 4 4 5 4 5 8 8 1 0 1 0 N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ N/ N/ N/ N/ N/ WL6023A00 , A0 Z A0 5 A1 0 230/208- 1 1 1 1 4 4 4 4 5 5 6 0 6 0 6 0 8 8 6 1 0 1 0 1 0 N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ N/ N/ N/ N/ N/ N/ N/ N/ WL6023B00 , B0 Z B0 9 230/208- 3 1 1 3 2 3 4 4 5 4 5 8 8 1 0 1 0 N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ N/ N/ N/ N/ N/ WL602NA00 , A0 Z A0 5 A1 0 230/208- 1 1 1 1 4 4 4 4 5 5 6 0 6 0 6 0 8 8 6 1 0 1 0 1 0 N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ N/ N/ N/ N/ N/ N/ N/ N/ WL602NB00 , B0 Z B0 9 230/208- 3 1 1 3 2 3 4 4 5 4 5 8 8 1 0 1 0 N/A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ A N/ N/ N/ N/ N/ N/ . Maximum size of the time delay fuse or . Based on 75° C copper wire. All Wiring must conform to NEC and . These “ minimum Circuit Ampacity” values are to be used for sizing Refer to the National Electric Code (latest revision), CAUTION: When more than one field power conductor circuit is run through Pay special attention to note 310 regarding Ampacity SHIPPING DAMAGE Upon receipt of equipment, the carton should be checked for external signs of shipping damage. If damage is found, the receiving party must contact the last carrier immediately, preferably in writing, requesting inspection by the carrier’s agent. GENERAL The equipment covered in this manual is to be installed by trained, experienced service and installation technicians. The refrigerant system is completely assembled and charged. All internal wiring is complete. The unit is designed for use with or without duct work. Flanges are provided for attaching the supply and return ducts. These instructions explain the recommended method to install the air cooled self-contained unit and the electrical wiring connections to the unit. While these instructions are intended as a general recommended guide, they do not supersede any national and/or local codes in any way. Authorities having jurisdiction should be consulted before the installation is made. See Page 1 for information on codes and standards. Size of unit for a proposed installation should be based on heat loss calculation made according to methods of Air Conditioning Contractors of America (ACCA). The air duct should be installed in accordance with the Standards of the National Fire Protection Association for the Installation of Air Conditioning and Ventilating Systems of Other Than Residence Type, NFPA No. 90A, and Residence Type Warm Air Heating and Air Conditioning Systems, NFPA No. 90B. Where local regulations are at a variance with instructions, installer should adhere to local codes. DUCT WORK All duct work, supply and return, must be properly sized for the design air flow requirement of the equipment. Air Conditioning Contractors of America (ACCA) is an excellent guide to proper sizing. All duct work or portions thereof not in the conditioned space should be properly insulated in order to both conserve energy and prevent condensation or moisture damage. These instructions and any instructions packaged with any separate equipment, required to make up the entire air conditioning system should be carefully read before beginning the installation. Note particularly any tags and/ or labels attached to the equipment. Design the duct work according to methods given by the Air Conditioning Contractors of America (ACCA). When duct runs through unheated spaces, it should be insulated with a minimum of one inch of insulation. Use insulation with a vapor barrier on the outside of the insulation. Flexible joints should be used to connect the duct work to the equipment in order to keep the noise transmission to a minimum. A 1/4 inch clearance to combustible material for the first three feet of duct attached to the outlet air frame is r...

Baixe o seu

Para fazer o download, introduza 2 dígitos :