Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
9 Control panel PAC400 24-04-2003 16:29 Pagina 10 Control panel PAC400 24-04-2003 16:29 Pagina 10 Timer ON/OFF pilot light ON/OFF button ON/OFF pilot light “Alarm” pilot light Thermostat A B C SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. If for example it is 4.00 p.m., turn the dial in a clockwise direction (following the direction of the arrow) until the number 4 is lined up with the arrow pointer (the arrows indicates 4:00 p.m. approximately). 11 9 4 10 arrow pointer Note:Never turn the dial in an counter-clockwise direction! The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then “slow”) and must be re-set. The unit can be used in either programmed or non-programmed mode. Timer ON/OFF Selecting fan button speed button PROGRAMMED MODE 1) esents 15 mins.). 3) ex. from 9 to 11 a.m. Release B timer button 2) Set the operating times by pushing out the notches on the dial corresponding to the peri- od required (each notch r Check that the timer indicates the correct time (see instructions on setting). 11 10 9 4 Operating time 4) Select the desired function as shown in the chart overleaf. The unit will now switch on and off each day at the selected times and the Timer ON/OFF pilot light will be on. Note: To override the programmed operating times, simply press the ON/OFF key. NON-PROGRAMMED MODE 1) B TIMER button must be pressed 2) Select the desired function as shown in the chart on the following page. For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (Pos.“Coolest”). When the desired temperature has been reached move the thermostat slider slowly away from the maximum cold position until the appliance is switched off by operation of the thermostat. In this way the appliance has been programmed with the exact temperature degree required, which is then maintained automatically by the thermostat 10 How to operate the air conditioner PAC400 24-04-2003 16:29 Pagina 11 How to operate the air conditioner PAC400 24-04-2003 16:29 Pagina 11 (REFER TO THE CONTROL PANEL ON THE OPPOSITE PAGE) Plug the appliance into the outlet. Select the “programmed” or “non pro- grammed” mode (see previous page) Select the fan speed required pressing “Fan speed” key C. AIR-CONDITIONING Turn the thermostat to Max. Cold. Press key A (ON/OFF). ON/OFF signal lamp (conditioning) will come on. The appliance comes on. If not, refer to pag. 13. To switch off the appliance, press key A (ON/OFF main switch). This appliance is fitted with a special safety circuit. When the compressor switches off, this circuit prevents it from switching on again for at least 3 minutes. 11 Cleaning and maintenance PAC400 24-04-2003 16:29 Pagina 12 Cleaning and maintenance PAC400 24-04-2003 16:29 Pagina 12 MAINTENANCE Always pull the plug from the electrical outlet before beginning any cleaning or maintenance operations. For safety reasons, never wash the air conditioner with water. CLEANING THE UNIT Clean your air-conditioner with a damp cloth and then wipe it with a dry cloth. Precautions: Never use gasoline, alcohol or solvents to clean this appliance. Never spray it with insecticide or similar liquids, because the paint might then peel off and the plastic portions might lose their true shape. CLEANING THE AIR FILTER • If the air filter gets dirty, it will be difficult for the air to circulate and the air-conditioner will lose much of its efficiency, thus leading to about an 8% increase in electrical consumption. For this reason, it is a good idea to clean the filter • Remove the air filter as shown below. Filter • Use a vacuum cleaner to remove the dust on the filter. If the filter is very dirty, dip it in warm water (of less than 40° C.) and rinse it several times. After having washed the filter, let it dry completely before putting it back in place. CHECKS TO MAKE AT A SEASON’S BEGINNING Check to make certain that the power cord and the electrical outlet are in perfect condition and that there is a suitable grounding system. Give strict observance to all installation norms. WORK TO BE DONE AT A SEASON’S END Turn off the air-conditioner. Clean the filter and dry it before putting it back in place. Cover the air conditioner with a plastic bag to keep the appliance from getting dusty. 12 Troubleshooting PAC400 24-04-2003 16:29 Pagina 13 Troubleshooting PAC400 24-04-2003 16:29 Pagina 13 IF SOMETHING GOES WRONG Most malfunctions are caused by a very minor and easily solved problem. So carefully check this list before contacting a Delonghi Service Center. PROBLEMS CAUSES REMEDIES The air conditioner does not function • Power failure • The appliance is not plugged in • Less than 3 minutes have passed since the appliance was last ...