Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• The appliance can be cleaned with a cloth or sponge, slightly warm water and a mild detergent. • Never use hot water (more than 40.C), bleach, petrol, acid, scouring pads, brushes or strong detergents. Prevent water from entering the appliance. • Do not clean the appliance with a water hose or compressed air. Cleaning and changing the purifying filters To change the purifying filter, it is first necessary to open the front flap on the appliance (it is not necessary to remove it). The user should lift the flap slightly holding it on the sides, see Fig. 29. The flap can be opened up to the safety stop without risk of falling. All models are fitted with a basic filter which needs to be cleaned regularly, Fig. 30. The filter is accessed by pressing the tab at the top and removing it from its housing, Fig. 31. The filter is cleaned under a cold tap, dried and replaced. Washable basic filter Fig. 29 Fig. 30 Fig. 31 Cleaning and Maintenance 48 • Remove the basic filter from the appliance, Fig. 31. • Insert the purifying filter + positioner inside the basic filter as shown on Fig. 33, remembering that it must be housed on the lower studs first. Prior to use at change of season • Clean the air filter. • Clean the casing and the grilles if necessary. Fig. 34 Fig. 35 filters more easily. When removing the flap or in the event of the flap coming out of position for whatever reason, the user should fit the plastic leg on the flap into the groove on the front of the appliance until it is properly rehoused. After refitting, make sure that the flap stops when its reaches the safety stop and does not fall. Storage requirements When the appliance is out of use for a long period, set the expulsion tube to parking position so that the appliance takes up as little space as possible. • To do this, bend the tube towards the back of the appliance and secure it with the diffusion hook, Fig. 34 and 35. Fig. 32 • Install the assembly onto the appliance by lining the lower studs up with the slots on the front casing of the appliance and pressing the top clip in until it clicks into position. The assembly is fitted properly when it clicks into position. • Close the front flap Warning! Fit only one set of filters onto the support in order to ensure correct appliance operation. Note: The flaps on these models are fitted with safety stops up to which point they can be opened without risk of the front flap falling and causing damage and/or injury. The flap can also be removed in order to clean the appliance or change the 2 clack! clack! 1 Fig. 33 Things to check before calling the Technical Service Things to check before calling the Technical Service General requirements for operation What to do if... ... the appliance does not work ... • Check that it is plugged in properly. • Make sure that the control knob is not set to off . • Check that the mains electricity supply is working. Check the fuse box. • Set the thermostat to its minimum temperature position. ... the appliance does not work and the light indicating that the condensed water tank is full is on ... • Set the appliance on a flat surface. If the light does not go out, empty the internal water tank. (See instructions in "Cooling"). ... the appliance does not work and the light indicating that the condensed water tank is full flashes... • This indicates heat sensor failure. Get in touch with the Technical Assistance Network. ... the appliance does not reduce room temperature sufficiently ... • Check the joins on the hot air expulsion tube. • CMake sure that the expulsion tube is not too bent and that it is not extended to more than 140 cm. • Make sure that the plug is fitted on the drainage water pipe. • Fit the suction pad to close the window as far as possible. • Lower blinds to reduce direct sunlight. ... there is water on the control panel grille or on the basic filter housing ... • There is no cause for concern. This is normal. Noise ... the appliance makes a lot of noise ... Some noise is normal and other types of noise can be solved easily. You need to be able to distinguish between these types of noise: Perfectly normal noise • The sound of water flowing in cycles is due to the pump, which circulates the water to enhance the power of the appliance. • A dull, humming sound is inevitable due to the compressor. • A faint, whistling sound is due to the refrigerant passing through the thinner pipes on the appliance when the compressor starts up. • A short clicking sound is produced when the pump connects and disconnects or when the regulator connects or disconnects the electronics system. Easy-to-solve noises • Make sure that the air expulsion tube and the diffusion and collection sleeves are fitted properly onto the appliance. • Make sure that the air intakes and outlets on the appliance are free of obstacles. • Make sure that the appliance is not in direct contact with furniture or other appliances. The air output may be flowing directly onto these and thereby increasing th...
Este manual também é adequado para os modelos :Aparelhos de ar condicionado - 3XM430E/02 (2.67 mb)