. . . . . . . . .2 Operating Instructions Controls—Dip Switches . . . . . .3–5 Controls—Terminal Connections . . . . . . . . . . . . . .6, 7 On/Off Switch . . . . . . . . . . . . . . .8 Ventilation Control . . . . . . . . . . .8 Care and Cleaning Air Filters . . . . . . . . . . . . . . . . . . .9 Base Pan . . . . . . . . . . . . . . . . . . .9 Exhaust Coils . . . . . . . . . . . . . . . .9 Installation Instructions Electrical Supply . . . . . . . . .11–13 Installing the Zoneline . . . .14–21 Pre

Branch Circuit and Proper GE Unit Amperage Rating Subbase Kit 15 RAK204D15P 20 RAK204D20P 30 RAK204D30P* 14 Installation Instructions 265 VOLT ELECTRICAL SUPPLY JUNCTION BOX Remove the junction box cover by taking out the Remove the junction box by taking out the top rear . Note how the tab on the lower right corner ves to hold the side in place. This will help when the box is being reinstalled. The cord will be coiled up inside the junction box. 1 Unit connector Junction box cover Junction box

Quick Reference 2500 Series Cooling with Electric Heat MODEL NUMBER COOLING (Btuh) Cooling Watts EER Electric Heat (Btuh) Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) AZ25E07D2* 7100/6900 600/585 11.8/11.8 8600/7100 2550/2090 11.0/10.0 15 AZ25E07D3* 7100/6900 600/585 11.8/11.8 11700/9600 3450/2820 15.0/13.6 20 AZ25E09D2* 9000/8800 785/765 11.5/11.5 8600/7100 2550/2090 11.0/10.0 15 AZ25E09D3* 9000/8800 785/765 11.5/11.5 11700/9600 3450/2820 15.0/13.6 20 AZ25E09D5* 9000/

• Includes 3-meter conductor wire for hook-up to Vertical Zoneline. • Required for Motion Sensor/Door Switch applications. * A-B Series: Zonelines® built before 1987 – Zoneline I, II, III, and IV; AZC Series: Zonelines built from 1987 to 1992 – includes AZR Series – Zoneline 1000, 2000, 2500, 2700, 3000, 4000, 5000; AZ Series: Zonelines built after 1992 – Zoneline 2100, 3100, 2600, 5100 / Zoneline 2200, 3200, 5200 / Zoneline 2500, 3500, 5500 / Zoneline 2800, 3800, 5800. RAVWP6 (AZ Series*—7500)

2. Carefully remove 6. of the cordset insulation so as to expose the three insulated wires. 3. Strip 3/4. of the insulation away at the end of each of the three wires (L1, L2 and Ground). 4. Direct connection to branch circuit wiring inside the provided junction box must be made by connecting as follows in steps 1–3 below. 3/4. 6. Connector 7. FOR 265 VOLT DIRECT CONNECT APPLICATIONS ONLY IMPORTANT: Connection of a 265V AC product to a branch circuit MUST be done by direct connection in accordan

. . . . . . . . . . . . . . . .3 Connect Electricity . . . . . . . . . . . . .2 Extension Cords . . . . . . . . . . . . . . .3 Safety Precautions . . . . . . . . . . . . . .2 Operating Instructions Controls—Control Knobs . . . . .6, 7 Controls—Touch Pads . . . . . . . .4, 5 Care and Cleaning Air Filter . . . . . . . . . . . . . . . . . . . . . . .8 Grille and Case . . . . . . . . . . . . . . . . .8 Outdoor Coils . . . . . . . . . . . . . . . . . .8 Installation Instructions Through the Wall Inst

Replacing an existing unit? For details, see the Installation Instructions in this manual. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS 2 About the controls on your Zoneline. ge.com TEMP CONTROL MODE CONTROL Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Consumer Support Controls Temp Control The temp control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same comfort level. When y

2 Connect to electrical power. 3 See the special instructions below for applicable supply voltages. 4 Reinstall the room cabinet. Branch Circuit and Proper GE Unit Amperage Rating Subbase Kit 15/20 RAK204D20 30 RAK204D30 230/208 VOLT ELECTRICAL SUPPLY All wiring, including installation of the receptacle, must be in accordance with the NEC and local codes, ordinances and regulations. This unit is equipped with a line cord for appropriate amperage wall receptacle. See below. Electrical subbases pr

REMOVE JUNCTION BOX 1 Remove the junction box cover by removing the front two screws. 2 Remove the junction box by removing the top and bottom rear screws. Note how the tabs on the lower left side of the junction box serve to hold the side in place. This will help when the box is being reinstalled. 1 Unit connector Junction box cover Junction box CUT AND STRIP THE CORDSET 1 Remove the cordset from the power supply kit. Measure 6. down the cord from where it emerges from the back of the nylon pla

For service in Canada, call 1.800.361.3400. Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. For The Period Of: GE Will Replace: One Year From the date of the original purchase Any part of the Zoneline which fails due to a defect in materials or workmanship. During this full one-year warranty, GE will also provide, free of charge, all labor and on-site service to replace the defective part. Five Years From the date of the original purc