Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Tighten motor mount bolts and recheck tension and pulley alignment. Figure 9. Pulley and V-belt alignment. Bearing Block Cutterhead Setscrews Setscrews Cutterhead Pulley Motor Pulley Fence Place the fence body on the fence support, making sure that it fits over the key. See Figure 10. Insert the locking screw and thread on the special nut provided. The flange on the special nut should protrude upward when installed correctly. Locking Screw Special Nut (Not In Sight) Figure 10. Fence support mechanism. NOTICE DO NOT slide the fence across the outfeed table. Scratching will result. -14- G1182 6" Series Jointers Cutter Guard Belt Guard 1. The cutterhead guard pivot shaft is slotted on the end. This slot fits over the tang at the end of a spring located in the spring housing. See Figure 11. Look down the pivot hole to get an idea where this tang is located. 2. Remove the setscrew from the slotted end of the pivot shaft. Rotate the spring housing counter-clockwise approximately 1 turn. Insert the guard shaft into the pivot hole, lining up the slot with the tang. 3. The cutterhead guard shaft should fit all the way inside the pivot hole when properly engaged with the spring tang and should hold the guard against the fence. 4. The cutterhead guard should be held firmly against the fence, completely cover the cutterhead, and move back into position when released. If this has not been achieved, repeat Steps 2-3, increasing the number of turns on the spring housing to 11.2. Re-install the setscrew into the end of the pivot shaft. Figure 11. Spring housing. Insert the 5.16" - 18 x 21.2" mounting bolt through the belt guard and attach to the jointer base casting. Do not over tighten. See Figure 12. Figure 12. Belt guard attachment. DO NOT attempt any step of assembly, adjustments, or maintenance while your Model G1182 is running. Ensure that the switch is off, power is disconnected and moving parts have stopped before making adjustments. Failure to comply may result in serious personal injury. G1182 6" Series Jointers -15 Knife Setting Gauge 1. Insert the steel rod through the hole in each adjuster arm until the notches for the E-clips extend past the adjustment arms on both sides. 2. Attach the E-clips to the notches to lock adjustment arms onto the steel rod. The adjustment arms are symmetrical, so the placement is not a concern. See Figure 13. Figure 13. Knife setting gauge. Pedestal Switch G1182ZX Only Your jointer comes with a pedestal mounted magnetic switch for safety and convenience. Simply bolt the pedestal to the two mounting holes on the back side of the stand with the supplied washers and bolts. See Figure 13A. Figure 13A. Mounting pedestal switch to stand. -16- G1182 6" Series Jointers SECTION 5: ADJUSTMENTS Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire adjustment process. Failure to comply may result in serious personal injury. Table Gibs Always lock the table with the table lock before using the jointer. If this step is not observed, the table could slide down while the jointer is operating. Serious personal injury may occur. The function of the gibs are to allow precise adjustment of the table movement along the dovetail ways. Adjustment of the gib will dictate how easy it will be to move the tables up and down with the levers or handwheels. To adjust gibs: 1. Unscrew the upper and lower check nuts on the infeed table several turns, leaving the lock handle tight. See Figure 14. 2. With one hand securely on the lever bar, loosen the table lock handle and adjust the G1182 6" Series Jointers Check Nuts Lock Handle Setscrews Figure 14. Location of check nuts. upper and lower gib setscrews until table movement is smooth and controlled. 3. Once the gib has been properly adjusted, tighten check nuts and repeat Steps 1-2 for the outfeed table. 4. Make sure there is no side-to-side movement of the tables once the check nuts have been tightened. If there is, repeat Steps 1-4. Knives These knives are extremely sharp. Never grab the cutterhead directly to rotate it. Always use the drive pulley. Always be sure the jointer is disconnected from its power source before you make any adjustments. Serious personal injury may occur. KNIFE INSPECTION The knives of your jointer must be periodically replaced or adjusted. Adjustments should be as precise as possible with tolerances within .002". 003" to prolong the sharpness of the knife edges. Improperly adjusted knives can unbalance the cutterhead and shorten bearing life, as well as produce substandard jointing or planing results. The knives are set at the factory using jack screws -17 before shipping. Springs are also included in the cutterhead supplied with your machine. They may be used instead of the jack screws depending on your preference. Now...
Este manual também é adequado para os modelos :marceneiro Placa - G1182ZHW (1.84 mb)
marceneiro Placa - G1182ZX (1.84 mb)