Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
features • solid oak top (11.2" thick) with double rows of bench dog holes for each vise. • two storage drawers (with ball bearing slides) that are 14" wide x 133.4" long x 21.4" deep. • sturdy adjustable steel legs with leveling foot pads. • two oak-faced vises with removable top plate and 4" leadscrew travel, 13" wide x 2" thick. • Four bench dogs. • all wood surfaces finished with durable lacquer. • overall dimensions: 62" wide x 30" in depth x 32"–39" tall. • Weight: 155 lbs. Inventory use the parts breakdown and listing on page 4 to perform an inventory of the shipment. if any nonproprietary parts are missing (e.g. a bolt or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. NOTICE If you cannot find an item on the inventory parts list, check the mounting location on the workbench or examine the packaging materials carefully. Some items are pre- installed for shipping purposes. Assembly Tools Needed Qty phillips screwdriver #2 ...................................... 1 Wrench or socket 1.2"........................................1 To assemble your workbench: 1. insert the four M8 x 30 screw anchors into the holes at the ends of the front and back drawer panels for both drawers, as shown in figure 2. figure 2. attaching drawer side panels. M8 x 30 screw anchors M4 x 30 Wood screws Copyright © oCtoBEr, 2008 By grizzly industrial, inC. WARNINg: NO pORTION Of THIS MANUAL MAy BE REpRODUCED IN ANy SHApE OR fORM WITHOUT THE WRITTEN AppROvAL Of gRIzzLy INDUSTRIAL, INC. #ts11313 printEd in China -2- T10157 Oak Workbench 2. A lign the drawer side panels with the drawer sub-assembly, as shown in Figure 2, then secure them with the M4 x 30 wood screws. 3. A ttach the ball bearing drawer slides to tops of the drawer side panels, as shown in Figure 3, with the M4 x 13 wood screws. Note: Make sure the drawer slides properly fit with the pre-installed slides underneath the workbench top, as shown in Figure 4. Figure 4. Aligning the drawer slides with the preinstalled slides. Align These Slides NOTICE When gluing parts together, wipe off the excess and allow the glue to completely dry before proceeding to avoid inadvertently gluing the wrong parts in subsequent steps. Figure 3. Attaching drawer slides to the drawers. Drawer Slides M4 x 13 Wood Screws 4. I nsert the tubes through the rear of the vise leadscrew assemblies and secure them with the 5.16"-18 hex nuts and 5.16" flat washers, as shown in Figure 5. 5. I nsert the handles through the ends of the vise leadscrew assemblies (see Figure 5) and glue on the knobs to hold them in place. 6. S lide the vise leadscrew assemblies into the vise faces and secure them with the 1.4" x 1 1.2" wood screws. 7. P osition the vise leadscrew plates underneath the table and align their holes with those in the table edges, then secure them in place with the 1.4" x 1 1.2" wood screws, as shown in Figure 6. Figure 5. Vise assembly. 5.16" Hex Nut & Flat Washer 1.4" x 1 1.2" Wood Screw Tube Handle & Knob Vise Face Figure 6. Vise leadscrew plate aligned with the underside of table and holes in the table edge. Vise Leadscrew Plate 1.4" x 1 1.2" Wood Screw T10157 Oak Workbench -3- Figure 7. Installing the legs. 5.16" 18 x 1" Flange Bolts 11. A ttach the leg supports to the leg assemblies with the 5.16"-18 x 1" flange bolts, as shown in Figure 7, then secure the leg assemblies to the workbench top with the 5.16"-18 x 1" flange bolts. 12. With assistance, flip the workbench right side up, then adjust the foot pads to make the top surface level. 13. A ttach the bottom shelf to the legs with the 5.16"-18 x 1.2" flange bolts, as shown in Figure 8. 14. I nsert the bench stop bars and the bench dogs into the workbench top to finish the assembly. 8. I nsert the vise assemblies through the holes in the table edge and thread the leadscrew into the leadscrew plate. 9. With assistance, turn the workbench top upside down on a flat, protected surface. 10. S lide the lower legs into the upper legs, then secure them together with the 5.16"-18 x 3.4" hex bolts and flat washers, as shown in Figure 7. Note: Make sure that the completed leg assemblies are all the same length, which will dictate the height of the finished workbench (from 32"–39"). 5.16"-18 x 3.4" Hex Bolts & Flat Washers Leg Support 5.16"-18 x 1" Flange Bolts Figure 8. Bottom shelf installed. Bottom Shelf Bench Dog 5.16" x 1.2" Flange Bolt Bench Stop Bar -4- T10157 Oak Workbench Parts Breakdown and List 1 2 4 5 6 8 7 9 11 10 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 27 25 REF PART # DESCRIPTION QTY REF PART # DESCRIPTION QTY 1 PT10157001 VISE LEADSCREW ASSEMBLY 2 17 PT10157017 DRAWER PANEL RIGHT 2 2 PT10157002 TUBE 4 18 PT10157018 DRAWER PANEL BACK 2 4 PT10157004 SCREW ANCHOR M8 X 30 16 19 PT10157019 DRAWER PANEL BOTTOM 2 5 PT10157005 WOOD SCREW M4 X 30 16 20 PT10157020 UPPER LEG 4 6 PT10157006 GLUE TUBE 1 21 PT10157021 LOWER LEG 4 7 PT10157007 BALL B...