Assessments - 3, GPA: 3.3 ( )

Fabricante : Bosch Arquivo Tamanho: 1.04 mb Arquivo Nome : Língua de Ensino:

To attach, place deflector into position as shown in (Fig. 10). Then flex sides of deflector while pushing until it snaps into place. The plunge base’s chip shield can also be flipped out. FIG. 10 210IN50403020100MM -11 BM 2610925542 07-06.qxp 7/24/06 12:06 PM Page 12 Operating Instructions A B FINE ADJUSTMENT DIAL BASE CLAMP LEVER COARSE ADJUSTMENT LEVER INDICATOR RING FIG. 11 CAST INDICATOR MARKS Bosch routers are designed for speed, accuracy and convenience in performing cabinet work, routing, fluting, beading, cove- cutting, dove tails, etc. They will enable you to accomplish inlay work, decorative edges and many types of special carving. DEPTH ADJUSTMENT WITH FIXED BASE Router’s RA1161 fixed base are equipped with a true micrometer type fine adjustment mechanism, which can be used in any position and provides precise adjustment of the router bit position for unmatched accuracy. When the tool is lowered to the approximate position desired, this device may be adjusted to precisely set the final bit position. Your router also features three horizontal notches on both sides of the motor housing for coarse adjustments. The notches are spaced 1/2" apart which allows you to quickly lower or raise the tool depth in three 1/2" increments. (Approximately 12.7 mm), by simply depressing the coarse adjustment release lever. TO ADJUST DEPTH NOTE: All depth adjustments must be made with the base clamp lever released. 1. Hold the tool in a horizontal position with the base clamp lever facing you. 2. Open the base clamp lever to release the motor. 3. COARSE ADJUSTMENT: To make a large depth adjustment, depress coarse adjustment release lever and raise or lower to desired depth. There are three notches in the motor housing which are spaced 1/2" to facilitate this adjustment. 4. FINE DEPTH ADJUSTMENT: To use the fine adjustment feature, turn the fine adjustment knob clockwise to lower the router bit or counter-clockwise to raise it. NOTE: Be sure coarse adjustment lever is engaged in one of the coarse adjustment notches before making a fine adjustment. To allow precise settings, the indicator ring is graduated in English and Metric increments. (Note: one full turn of fine adjustment knob = 1/16" or approximately 1.5 mm. The fine adjustment mechanism has a total adjustment range of 7/8" (23 mm). Each cast indicator mark next to coarse adjustment lever is equal to 1/8" To prevent damage to tool, avoid wedging the coarse adjustment lever against the upper A or lower B portion of the housing as shown in figure 11. 5. After making depth adjustments, re-clamp the motor. The indicator ring may be reset to zero without moving the fine adjustment knob, to allow the user to begin the adjustment from any reference point desired. -12 BM 2610925542 07-06.qxp 7/24/06 12:06 PM Page 13 When the router is installed in a router table, it can be adjusted with a 1/8” hex wrench, not included with all models. (See page 21). The RA1002 Fine Adjustment Control Extension, an optional accessory for the non- plunge bases, allows fine adjustment from beyond the top of the motor housing. To install, simply press the RA1002 into the end of the base’s own fine adjustment knob. (Fig. 12) TO CLAMP MOTOR When final coarse and fine adjustments have been made, fasten the base clamp lever to secure adjustments. (If additional clamping force is desired: using a 10 mm wrench, rotate clamp nut clockwise SLIGHTLY (1/8 turn or less), then test clamp. Do not overtighten.) DEEP CUTS For deeper cuts, make several progressively deeper cuts by starting at one depth and then make several subsequent passes, increasing the cutting depth with each pass. To be certain that your depth settings are as desired, you may want to make test cuts in scrap material before beginning work. FIG. 12 DEPTH ADJUSTMENT WITH PLUNGE BASE PLUNGING ACTION The plunge feature simplifies depth adjustments and will allow the cutting bit to easily and accurately enter the workpiece. To lower, push plunge lock lever to the left, apply downward pressure until you reach desired depth, and release pressure on lever to lock (Fig. 13). The plunge lock lever is spring loaded and returns automatically to the locked position. To raise the router, push plunge lock lever to the left, release pressure on router and the router will automatically retract the bit from the workpiece. It is advisable to retract the bit whenever it is not engaged in workpiece. DEPTH ROD AND TURRET The depth rod and the depth stop turret are used to control cutting depth as follows; 1. With the bit installed, gently lower the motor until the tip of the router bit just contacts the level surface the router is sitting on. This is the “zero” position, from which further depth adjustments can be accurately made. 2. To set a desired depth of cut, rotate depth stop turret until the lowest step is aligned with the depth rod. Loosen depth indicator knob and lower the depth rod until it contacts the lowest step of the turret. Slide the dep...

Baixe o seu

Para fazer o download, introduza 2 dígitos :