The stopper block is also convenient for making three passes with progressively deeper bit settings when cutting deep grooves. CAUTION: • When using a bit having total length of 60 mm (2 - 3/8”) or more, or edge length of 35 mm (1 - 3/8”) or more, the depth of cut cannot be adjusted as previously mentioned. To adjust, proceed as follows: Loosen the lock lever and carefully adjust bit protrusion below the tool base to the desired depth of cut by moving the tool body up or down. Then re-tighten th

If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 4. Check the bit carefully for cracks or dam- when performing an operation where the age before operation. Replace cracked or cutting tool may contact hidden wiring or damaged bit immediately. its own cord. Contact with a “live” wire will 5. Avoid cutting nails. Inspect for and make exposed metal parts of the tool “live” remove all nails from the workpiece and shock t

Replace cracked or cutting tool may contact hidden wiring or damaged bit immediately. its own cord. Contact with a “live” wire will 5. Avoid cutting nails. Inspect for and make exposed metal parts of the tool “live” remove all nails from the workpiece and shock the operator. before operation. 2. Wear hearing protection during extended 6. Hold the tool firmly. period of operation. 7. Keep hands away from rotating parts. 3. Handle the bits very carefully. 8. Make sure the bit is not contacting the

Do not force it past 6 or 1, or the speed adjusting function may no longer work. ASSEMBLY ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit CAUTION: • Do not tighten the collet chuck without inserting a bit, or the collet chuck will break. • When using bit of bigger than 1-1/4” in diameter, install base plate with center hole diameter 2-1/2”, replacing the original base plate. 003672 First, remo

If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating Volts Total length of cord in feet 120 V 25 ft. 50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended GROUNDING INSTRUCTIONS This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a three-conductor cord and three-prong grounding t

Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. Motor unit cord 2. Outlet 3. Lock button 4. Switch trigger 003663 For RD1100 and RD1101 1 CAUTION: • Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” 3 position when released. 4 • Switch can be locked in “ON” position f

They may cause cracks in the tool base. 16. Draw attention to the need to use cutters of the correct shank diameter and suitable for the speed of the tool. 17. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD101-2 The followings show the sym

Do not force it past 5 or 1, or the speed adjusting function may no longer work. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003670 Installing or removing the bit CAUTION: • Install the bit securely. Always use only the wrench provided with the tool. A loose or overtightened bit can be dangerous. • Do not tighten the collet nut without inserting a bit or install small shank bits without using a collet sleeve. Either can lead to