All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 Specifications Material Molded phenolic plastic, steel accessories. Dimensions 12” x 9” x 23/64 thick Main Opening 3-7/8” inside demension Guide Pin 1-3/8” L x 1/4” DIA. (pin) x 3/8” DIA. (shoulder) Large Pop Out Ring 4-1/16” OD x 2-9/16” IDSmall

(1). Insert T-Screw (4) from underneath through Guide (2), Fence (1) and Washer (15). Screw Lock Knob (3) onto T-Screw (4) and tighten clockwise. Attach the other Guide using the same procedure. To attach and secure the Router Table Fence on a Router Bed, slide the two Guides (2) onto the rails on the Router Bed. (See Assy. Diagram.) Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set

Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. D

Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES IMPORTANT SAFETY INSTRUCTIONS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions detailed in this manual may result in serious personal injury. SAVE THESE INSTRUCTIONS 1. Keep your work area clean and well lit. Cluttered and dark work areas invite accidents. 2. Stay alert. Watch what you are doing, and use common

SAFETY WARNINGS AND PRECAUTIONS 1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle this product. 3. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 4. USE EYE PROTECTION. Wear ANSI-approved safety impact e

(See Figure C.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a FIGURE C damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. Double Insulated SYMBOLOGY Canadian Stan

2. The V-Belt is slipping. 1. Make sure machine is plugged into a working, 110 volt, grounded, electrical outlet. 2. Adjust V-Belt tighter, or replace Belt. The Wood Shaper vibrates. The Spindle is loose. Or the Cutter “chatters”. 1. The Stand of the Wood Shaper is unstable and wobbles. 2. The Spindle or Cutter is loose or out of alignment. 3. The Wood Shaper has a loose Motor or Spindle Cartridge. 1. Stabilize the Stand on the floor. 2. Reinstall the Spindle and/or Cutter. 3. Have a qualified s

Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.) To AttachThe Motor Assembly: 1. Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjust

Before assembling, remove all traces of the packing grease from the Jointer and wipe all parts thoroughly with a clean dry cloth. When cleaning do not use acetone, gasoline or paint thinner as these solvents are dangerous to you and may also cause damage to plastic and rubber parts. Apply a thin coating of automotive wax to any unpainted surfaces to prevent rust. Caution!: Consider the weight of the components and take the necessary precautions when lifting. Assistance may be required during ass

Accessory Diameter 2” Shank Diameter Router: 1/4” Shaper: 1/2” Table Top 11-3/4” x 9-3/4” surface Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. Components Figure 1Table Insert (8) Carbon Brushes (3b) Belt (34) Double Ended Wrench (55) Nut (49) Spindle Wrench (54) Keyed Washer (48) Switch Key (27b) Washer (13) Radius Pin (6) Collar (53) Router Bit Collet (50) Sh