Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
45-0355-131 CAUTION: Read Rules for Safe Operation and Instructions Carefully 3 PT. HITCH TANG CULTIVATOR • Safety • Assembly • Operation • Maintenance • Parts thefastestway topurchaseparts PRINTED IN USA FORM NO. 49358 (4/04) 2 SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. 1. Read this owner's manual before using this equipment. 2. Do not allow children to operate the tow vehicle or the tine cultivator. 3. Do not allow adults to operate the tow vehicle or the tine cultivator without proper instruction. 4. Do not allow anyone to ride on the tow vehicle or the tine cultivator. 5. Before lowering the tine cultivator, make sure no one is near the area of operation. 6. Lower the tine cultivator when leaving the tow vehicle unattended. 7. Wear appropriate footwear when using the tine cultivator. The tip of each tang on the cultivator is pointed and sharp! 8. Tow vehicle braking and stability may be affected by the tine cultivator. Drive slowly with the tine cultivator in the transport position. Stay off steep slopes. 9. Stop and inspect the equipment for damage after striking an object. Repair any damage before continuing operation. 10. Keep all nuts and bolts tight and be sure that the equipment is in safe operating condition. 11. Before attaching or removing the tine cultivator, park and lock the tow vehicle in a safe condition. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS – ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED BY THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. CARTON CONTENTS 1. Cross Brace 2. Depth Gauge Bar (2) 3. Weight Bracket 4. Mast Extension Strap (2) 5. Mast Side (2) 6. Mast Lift Strap (2) 7. Support Bracket 8. Cultivator Assembly Parts Package (see page 3) 1 2 4 6 3 5 7 8 E K J F G I D H C B A L M N E K J GF I D H C B A L M N PARTS PACKAGE CONTENTS – PARTS SHOWN ACTUAL SIZE KEY QTY. DESCRIPTION KEY QTY. DESCRIPTION A B C D E F G 2 1 1 2 2 2 1 Category 1 Pin Pivot Pin Haircotter Pin, 1/8" Hex Bolt, 3/8" x 2-1/4" Lg. Hex Bolt, 1/2" x 1-1/2" Lg. Hex Bolt, 1/2" x 2-3/4" Lg. Hex Bolt, 1/2" x 3-1/2" Lg. H I J K L M N 2 8 2 5 1 2 2 Hex Bolt, 3/8" x 1" Lg. Hex Nut, Nylock, 3/8" U-Bolt, 3/8" Hex Nut, Nylock, 1/2" Spacer Lock Washer, 7/8" Hex Nut, 7/8" 3 4 ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY (2) 3/4" Wrenches (2) 9/16" Wrenches (2) 1-1/8" Wrenches or Adjustable Wrenches (1) 1-5/16" Wrench or 12" Adjustable Wrench Remove all loose parts and the hardware package from the shipping carton. Lay out and identify each part and the hardware as shown on pages 2 and 3. Be sure the carton is empty before it is discarded. 1. Attach two depth gauge bars to the frame using a 3/8" U-bolt and two 3/8" Nylock hex nuts for each bar. Put each depth gauge bar next to each outside tang on the rear of the frame as shown in figure 1. Use the holes in each bar that will give the desired working depth, if known at this time. Use matching holes in both depth gauge bars to keep the cultivator level. NOTE: For effective depth control a depth gauge bar must not be located directly behind a front tang. 2. Attach two mast extension straps to the front of the frame using two 1/2" x 2-3/4" hex bolts and two 1/2" Nylock hex nuts. Point the bent end of each strap toward the outside of the frame. Do not tighten yet. See figure 2. CAUTION: THE CULTIVATOR TANGS HAVE SHARP POINTS. USE CARE WHEN HANDLING AND ASSEMBLING THE TANGS. WEAR GLOVES FOR EXTRA PROTECTION AGAINST CUTS. FIGURE 2 1/2" NYLOCK HEX NUT MAST EXTENSION STRAP (RIGHT SIDE) 1/2" x 2-3/4" HEX BOLT FRONT FIGURE 1 3/8" NYLOCK HEX NUT 3/8" U-BOLT DEPTH GAUGE BAR DEPTH GAUGE BAR 3. Attach the cross brace and the two mast sides to the ends of the mast extension straps. The cross brace is between the extension straps while the mast sides are on the outside. The cross brace and mast sides are connected to the extension straps using two category 1 pins, two 7/8" lock washers, and two 7/8" hex nuts. Do not tighten yet. See figure 3. WORKING DEPTH FIGURE 3 MAST SIDE CATEGORY 1 PIN CROSS BRACE 7/8" LOCK WASHER 7/8" HEX NUT EXTENSION STRAP 5 4. Arrange the mast lift straps as shown in figure 4. Place the straps and the spacer between the mast sides, fastening them to the lower hole in the mast sides using a 1/2" x 3-1/2" hex bolt and 1/2" Nylock hex nut. Do not tighten yet. FIGURE 4 MAST LIFT STRAP SPACER 1/2" NYLOCK HEX NUT 1/2" x 3-1/2" HEX BOLT FIGURE 6 1/2" x 1-1/2" HEX BOLT 1/2" NYLOCK HEX NUT SUPPORT BRACKET MAST LIFT STRAP FIGURE 5 PIVOT PIN 1/8" HAIR COTTER PIN 5. Install the pivot pin through the upper hole at the end of the mast sides. Secure the pivot pin with a 1/8" hair cotter pin. See figure 5. 6. Attach the lower end of each mast lift strap to the outside of the welded fr...