Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
8). 3. Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb and fuel lines (Fig. 9). If you can’t see fuel in the bulb, press and release the bulb as many times as it takes before you can see fuel in it. 4. Push the blue EZ Fire™ Lever towards the primer bulb until it clicks and locks into place (Fig. 9). 5. Lay the unit on the ground horizontally, with the ends of the handles resting on the ground (Fig. 10). 6. Put your free hand on the fuel tank to stabilize the unit. With your other hand, pull the starter rope out with a controlled and steady motion until the engine attempts to start. Repeat until the engine starts. NOTE: The unit uses the Incredi-Pull™ starting system, which significantly reduces the effort required to start the engine. You must pull the starter rope out far enough to hear the engine attempt to start. There is no need to pull the rope briskly-- there is no harsh resistance when pulling. Be aware that this starting method is vastly different from (and much easier than) what you may be used to. 7. When the engine starts, squeeze the throttle control for 15 to 30 seconds. This will warm up the unit. The EZ Fire™ Lever will click off automatically when you squeeze the throttle control. IF... The engine does not start, go back to step 3. IF... The engine stops while you are squeezing the throttle, go back to step 4. IF... The engine stops before you squeeze the throttle control, hold the throttle control and pull the starter rope until the trimmer starts. NOTE: If you are having trouble starting the unit or are operating in extreme temperatures (below 40. F, above 90. F), refer to the Troubleshooting section. ON (I) OFF (O) Throttle Control Fig. 9 Primer Bulb EZ Fire™ Lever Fig. 8 Operate this unit only in a well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 10). To avoid serious injury, the operator and unit must be in a stable position while starting. WARNING: Fig. 10 Starting Position Mini-Tiller Equipped With Incredi-Pull Starting OPERATING INSTRUCTIONS OPERATING TIPS Dress properly to reduce the risk of injury when operating this unit. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy long pants, boots and gloves. Do not wear short pants, sandals or operate barefoot. WARNING: 2. Start the unit by following the Starting Instructions. 3. With the engine running and the tines off the ground, depress the throttle control to increase the engine speed. 4. Holding both of the handlebar grips firmly, slowly lower the cultivator until the tines make contact with the ground (Fig. 11). 5. As cultivating action begins, pull back on the cultivator so that the tines can penetrate the ground. 6. Once the ground has been broken, continue at a moderate pace until you are familiar with the controls and the handling of the cultivator. 7. To improve the depth of cultivation, pull back on the unit as it moves forward to drive the tines deeper into the ground. To prevent serious WARNING: personal injury, use extreme caution when reversing or pulling the unit towards you. 8. If the tines are digging too deep or not deep enough, adjust them according to Adjusting Tine Depth. Transport Grip Fig. 11 TRANSPORTING THE UNIT To prevent serious WARNING: personal injury, always stop the engine when operation is delayed or when transporting the unit from one location to another 1. Stop the engine. 2. Slide the roller bracket assembly all the way down. 3. Tilt the unit back until the tines clear the ground. 4. Push or pull the unit to the next location. 5. If you need to move the unit over long distances, use the transport grip. 1. Move the cultivator to the work area prior to starting the engine. Transport the cultivator by pushing it on its roller wheel or by carrying it by the transport grip. To prevent serious WARNING: personal injury, never pick-up or carry the unit while the engine is running. 12 MAINTENANCE AND REPAIR INSTRUCTIONS Fig. 12a TINE REMOVAL AND REPLACEMENT All 4 tines should be replaced at the same time because they will wear evenly through normal use. Work on one side at a time. 1. Put the On/Off Stop Control in the STOP (O) position and disconnect the spark plug boot from the plug. NOTE: It may be necessary to lay the cultivator back in a horizontal position on a flat level surface with the handles touching the ground. 2. Remove the click pin from each end of the tine shaft. Slide the tines off of the shaft (Fig. 12a). 3. Clean and oil the shaft. 4. When you are reinstalling tines, lay out the tines and compare them to those shown in Figure 12b. Note specifics about each tine: its hub, curvature and lettering (“A” or “B”). This will help make sure that you are placing the correct tines in the correct order. NOTE: If you look closely, you can see ...