Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
2 – 5 – KEYPAD Fig. 3 + + — Selects the Mode: WEIGH, WEIGH + PRESET, COUNT, COUNT + PRESET. — Selects LB as the unit of measure for Weigh mode (kg for metric). — Selects OZ as the unit of measure for Weigh mode (gm for metric). — Sets the platter weight as Tare (up to 2 lb or 1 kg); two beeps sound; >0< is not lit; clear platter to display the negative amount. Press for a full second to zero the scale; – 0 – displays while the scale rezeroes (up to 0.11 lb); then >0< is lit with 0.00 displayed. — Up arrow increases the Slice Count by 1, the Preset Weight by 0.01 LB, or 0.1 OZ in operator or program modes or advances through the six programmed preset values for the indicated mode when Preset is on. Indicator lights show the mode, unit of measure, and the number of the preset value. — Down arrow decreases the Slice Count by 1, the Preset Weight by 0.01 LB, or 0.1 OZ in operator or program modes or advances through the six programmed preset values for the indicated mode when Preset is on. Indicator lights show the mode, unit of measure, and the number of the preset value. — Hare increases the Carriage Speed by one level. The Carriage Speed is indicated by the number of lights. — Tortoise decreases the Carriage Speed by one level. The Carriage Speed is indicated by the number of lights. — Slice / Pause button starts the Knife and Carriage motors when in Automatic Mode only. If Slice / Pause is pressed while running, the Carriage returns to Home and stops. If Slice / Pause is pressed after an interruption, slicing restarts. Press Slice / Pause button with your thumb. BEEP — Short tone for a valid key. Long tone for an invalid key. Two short tones, enter Program Mode or Rezero. – 6 – PRESET VALUES — U.S. WEIGHT UNITS PRESET VALUES — U.S. WEIGHT UNITS FACTORY PRESET VALUES — U.S. WEIGHT UNITS MODE Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 WEIGH — LB 0.25 0.50 0.75 1.00 1.50 2.00 WEIGH — OZ 2.0 4.0 6.0 8.0 10.0 12.0 SLICE COUNT 4 6 8 10 15 20 PROGRAMMING To enter Program Mode with slicer controls lit and lever on Automatic: Hold down the Mode key for 6 seconds until 2 beeps sound and [Prog] displays for 2 seconds. Release the Mode key. The blinking PRESET indicates Program Mode. The CARRIAGE SPEED light(s) and the WEIGH (LB or OZ) or COUNT indicator lights show which Preset value is displayed. There are six preset values for each of the three categories (eighteen total). Do not interrupt power during programming. 1. Press the Mode key to select COUNT or WEIGH Mode. In WEIGH Mode, press both Mode and Up arrow keys at the same time to weigh in LB units; or, press Mode and Down arrow keys at the same time to select OZ units. 2. Press the Up and Down arrow keys to increase or decrease the Preset value. 3. Press Hare or Tortoise keys to access any Preset value (1 – 6) indicated by the CARRIAGE SPEED lights for the indicated category. Repeat steps 1, 2, and 3 to review or change any of the 6 Preset values for any of the 3 categories (18 preset values in all). When all Preset values are programmed as desired, press the Mode key for 2 seconds to Save and Exit. A beep sounds. [ If 0 is programmed as a Preset value, the slicer will Count Up until slicing is stopped by the operator.] CAPACITY The scale weighs according to the following capacity limits: U.S. Pounds U.S. Ounces Kilograms Grams 6 lb by .01 lb increment 96 oz by 0.1 oz increment 3 kg by .005 kg increment 3000 gm by 5 gm increments SLICE AND WEIGH MORE THAN ONE ITEM After slicing an item in weight mode, press Tare to set the weight back to zero without removing the sliced product from the platter. Then, with the scale display at 0.00 lb, slice and weigh the next item. PRESET VALUES — METRIC WEIGHT UNITS ONLY The six preset values for each weigh mode and slice count provided at the factory for metric weight units are shown in the table below. Other values can be programmed in place of these values by following the Programming instructions in the previous section. FACTORY PRESET VALUES — METRIC WEIGHT UNITS MODE Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 WEIGH — kg 0.100 0.200 0.300 0.400 0.500 1.000 WEIGH — gm 100. 200. 300. 400. 500. 1000. SLICE COUNT 4 6 8 10 15 20 – 7 – KEYBOARD AND DISPLAY ACTIVATION KEYBOARD AND DISPLAY ACTIVATION Automatic Mode — With the Lever on Automatic (pointing to the right) the keyboard display remains on only if the Switch Knob is on, the gauge plate is open, and the carriage is either at Home position or in motion during slicing. SLICING WITH PRESETS Using a Preset or Entered Value in Weigh Mode With the lever on Automatic, press the Mode key until WEIGH and either LB or OZ is lit to indicate Weigh mode and the units. The zero indicator, –> 0 <– , will be lit if the platter is empty; press Tare –> 0 <– to rezero the platter, if necessary. Once a Preset value is selected and the Preset indicator is lit, the entered or Preset value displays for only 2 seconds, then the platter weight displays. With the gauge plat...
Este manual também é adequado para os modelos :Panelas - 2912PS ML-104966 (2.39 mb)