Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
2000) Installation, Operation, and Care of HCM61 & HCM62 Food Processors SAVE THESE INSTRUCTIONS GENERAL The model HCM61 and HCM62 Food Processors are used for chopping meat, fish, fruits, vegetables, nuts, or dry bread, for mixing various sauces, mayonnaise, or soups, or for blending or pureeing various products, such as thickening or desserts. Refer to Capacity Recommendations, page 6. The HCM61 has a 1.5 HP motor, is provided with 120 Volt cord and plug, and requires a 20 Amp. electrical service and receptacle. The machine operates at 1700 rpm with single speed or pulse control. The HCM62 has a 2.0 HP motor, is provided with 208 - 240 Volt three phase cord and plug, and requires a 20 Amp. electrical service and receptacle. The machine operates at 1700 or 3400 rpm with two speed or pulse control. INSTALLATION UNPACKING Immediately after unpacking the food processor, check for possible shipping damage. If this machine is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate. Lift or move the machine only by using the two handles on the sides of the base. LOCATION Place the food processor on a suitable sturdy worktop or table. There should be adequate space around the machine for the user to operate the controls and install and remove the bowl and knife. Model HCM61 or HCM62Food Processor © HOBART CORPORATION, 2000 – 2 – ELECTRICAL CONNECTIONS (Cord Connected Machines) WARNING: THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A GROUNDING TYPE PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG. Refer to the machine data plate and Electrical Data, below. ELECTRICAL DATA ATADLACIRTCELEATADLACIRTCELEATADLACIRTCEEEELATADLACIRTCELATADLACIRTCEL Model ledoMledoMleMMMdoledoledo Volts / Hertz / Phase esahP/ztreH/stloVesahP/ztreH/stloVesahP/ztreH/stVVVloesahP/ztreH/stloesahP/ztreH/stlo Minimum Circuit Ampacity yticapmAtiucriCmuminiMyticapmAtiucriCmuminiMyticapmAtiucriCmumiMMMniyticapmAtiucriCmuminiyticapmAtiucriCmumini Maximum Protective Device eciveDevitcetorPmumixaMeciveDevitcetorPmumixaMeciveDevitcetorPmumiMMMxaeciveDevitcetorPmumixaeciveDevitcetorPmumixa AMPS SPMASPMASAAAPMSPMSPM Receptacle elcatpeceRelcatpeceRelcatpeRRRceelcatpeceelcatpece g ggg Pg PgPg Plu ululPuPPlulul HCM61 120 / 60 / 1 20 5-20R G W Plug: 5-20P HCM62 208 -240 / 60 / 3 20 L15-20R X G Z Y Plug: L15-20P Compiled in accordance with the National Electrical Code, NFPA70, latest edition. CHECK MOTOR ROTATION (Three-Phase Machines Only) On model HCM62, check the rotation. With all parts in their normal operating positions (pages 4 – 5), turn the switch to the Pulse position for two seconds and release. The direction of rotation of the knife should be counterclockwise as viewed from the top. If the knife rotates clockwise, correct the rotation using the following procedure: DISCONNECT THE ELECTRICAL POWER SUPPLY. Interchange any two of the incoming power supply leads in the plug. Reconnect the power supply and turn the switch to the Pulse position to verify that the knife rotates counterclockwise as viewed from the top. PRESTART CHECK With the machine fully assembled (pages 4 – 5), make sure the cutting blades stop within 4 seconds after the arm is swung back away from the center of the bowl cover. Make sure the machine cannot be started with the bowl and cover removed but with the arm swung into position above the center of the drive shaft. If the machine fails to work properly, contact Service; do not allow the machine to be operated. – 3 – BOWL AND KNIFE ASSEMBLY Install the Bowl so the center post of the Bowl fits over the motor shaft, one of the Bowl Pins fits in the slot at the front of the machine, and the bowl handles are positioned on left and right (Fig. 1). Install Knife Shaft over center bowl post so the slots on the Knife Shaft fit the grooves on the motor shaft (Fig. 1). The four Bowl Scraper Wipers must be properly installed in the grooves of the Bowl Scraper. The upper tips of the wipers point straight up and slightly toward the center (Fig. 2); the ends of the wipers are vertical so they do not interfere with the lip of the Bowl Cover. Do not install the wipers backwards. After installing the Lid Plug, turn it so the underneath side of the plug is flat with the underneath side of the Bowl Cover (Fig. 3). The Bowl Cover Gasket must be properly installed in the groove around the lip of the Bowl Cover (Fig. 3). ARM MOTOR SHAFT KNIFE SHAFT SLOT BOWL HANDLE BOWL BOWL PIN PL-41421-1 Fig. 1 TIP WIPER PL-41422-1 BOWL SCRAPER END Fig. 2 BOWL COVER GASKET BOWL COVER LIP ALIGMENT PIN LID PLUG PL-41423-1 Fig. 3 – 4 – Fit the Bowl Cover over the Bowl Scraper so the center holes align. Fit the Scraper Handle Shaft through the...