Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
If the laminate is not adhering to the hub in the same manner as the rest of the disc, you may wish to avoid laminating the center hub. To do this, lift the Tray Disc Hub Spacer from the center of the Disc Tray and rotate it slightly clockwise. Place it back into the center of the Disc Tray making certain it seats properly in the tray. 2. Repeat the test with another disc. When you are satisfied with the setting, you may want to make a note of them for future reference. You are now ready to laminate your discs. IMPORTANT:Due to the wide best transfer. If the laminate is to the disc, the However, if the heat is set too Excessive heat may even cause the label side Because of this you should heat necessary to transfer the laminate With the Disc Tray Hub in this position, laminate will NOT be transferred to the hub of the disc. CD/DVD Optical Disc Laminator Quick Start P/N 510893-021505 © 2005 All rights reserved. Congratulations of your ™ Disc to in this "Laminator"). This Quick Start step process of setting This includes information on how to and disc media) to start laminating discs. For more complete information regarding all aspects of to the User's Manual. 2 2 Installing Lamination (continued) 4. Insert the Overlaminate in the rear set of hubs inside Laminator as shown, keeping in mind that the Applying the Power Laminate will feed from 1. Locate the power cord supplied with over the top your Laminator. of the roll 12 Installing Lamination Ribbons 1. Press the Access Cover Button to open the Access Cover. 2. Remove the Overlaminate Film and Take-Up Core from its packaging. The film comes pre-rolled on a corewith a separate Take-Up Core included in the package. 3. Place the Take-Up Core in the front of the Laminator between the blackplastic Ribbon Drive Hubs asshown. The left-side Hub is springloaded. The right-side Hub has tabsthat willengage andlock in placewith thenotches in theright-side ofthe Take-Up Core. Access CoverButton SupplyTake-Up 2. Place one end of the power cord into 3 and the the power port located on the rear notches in panel of the Laminator. the core will need to face the right- side of the laminator to lock in place 3. Plug the power cord into an available with the ribbon drive hub. outlet. Avoid plugging your Laminator into a battery backup or uninterruptible 5. The white portion of the leading power supply. edge of Overlaminate film has an adhesive coating. Pull About Lamination Film and Optical Media it forward as Lamination Film for your Optical Disc shown, Laminator is available in both a clear and attaching it holographic finish. The Holographic to the front Overlaminate is used as a security feature Take-Up core. making your discs easily identifiable as Turn the authentic. Holographic Overlaminate is Take-Up also available with your own design when Core towards the front of the purchased in quantity. Please contact your laminator over the top to ensuredealer for details. Most inkjet printable the Overlaminate film is securelydiscs will work well with some adjusting attached. When properly loaded thefor heat. Because it is impossible to test all film will feed from over the top oftypes of media, it is highly recommended the supply roll in back and willyou purchase a small amount for testing travel over the top of the Take-Up before committing to a large, bulk Core in front. purchase of media. If you are having trouble with lamination quality, consider purchasing Accent Laminating Discs in Stand Certified Media Kits. Kits contain CDs or Alone Operation DVDs that are specifically tested and certified for use with the Accent. These Now that you have successfully loaded discs are the best possible combination of the Lamination Film, you are ready to burnable surface, printable surface and laminate your discs. lamination surface. For more information, 1. Turn the Laminator Power Switch to visit our web store at the ON position. Press the Laminate button. The Disc Tray should automatically eject from the Laminator and the Thermal Roller 3 Laminating Alone Operation (continued) will start heating up temperature. Move the Control Lever to the desired (The middle setting is recommend-ed initially.) The Ready LED should flash intermittently while the roller is heating. The process should take about 8-15 minutes. NOTE: The Laminator will automatically go into 'cool down' mode after 30 minutes of inactivity. 2. Once the READY LED is on and steady, the Laminator is at heat and ready to laminate your discs. You may need to make adjustments to the Laminator heat settings to ensure high quality output. Start with a test lamination to see if any adjustment will need to be made. This is done as follows: a. Place a disc on the Disc Tray. b. Press the Laminate Button. c. The disc will be drawn into the Laminator, laminated and the tray will be ejected. d. Examine the disc. If the lamina-tion looks spotty, more heat is required. Increase the intensity. If the lamination shows sc...