Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Liquefied or tacky adhesive will deposit on the heat rollers if the following procedure is not observed. Grab hold of the web. (top and bottom film), and install feed table under the web. Lower the safety shield and press the SPEED (>»-•) button to indicate 3 or less on the display panel. Hold down the RUN and REVERSE buttons together and guide the web out the front of the laminator. Make certain no exposed adhesive contacts the heat rollers and the film completely exits the laminator. 5. Release the buttons and press STOP after the web has cleared the heat rollers. 6. Lift safety shield to the full upright position. 7. Remove the feed table. 8. Lower the bottom idler bar, (Figure 7). 9. Remove the bottom film shaft by sliding the shaft to the right until the left side of the shaft dears the hex shaped brake hub. Loosen locking screw on left retaining collar of film supply shaft, and slide collar off. PuH shaft partially out of film tube, then push back in to knock out left core adapter. Pull shaft all the way out and rotate tube 180 degreos. Use shaft to knock out remaining core adapter. 10. Slide one core adapter Into right side of new roll of film ensuring that the film will unroll from the bottom on Poly-In film and from the top for Poly-Out film. Slide the film shaft into the core adapter and tube from the right side. Place the other core adapter on the shaft protruding from the left side then replace retaining collar. Tighten locking screw. 11. Unroll 2 ft. (61 cm) of film. Push the leading edge under and around bottom film guide. Slide film guide back into place and drape film over the front support for the feed table, (Figure 8). 12. Remove top film supply roll from laminator. Repeat steps 9 and 10 from above ensuring the film will unroll from the bottom after the film supply shaft is placod back on the laminator. 13. Unroll 2 ft. (61 cm) of film. Drape the film over the top idler bar and completely cover both heat rollers. (Figure 9). 14. Slide the feed tray under the piece of film that is draped over the bottom roll. Reinstall the feed table so that the bottom roll of film is resting on the tray. 15. Slide the threading card between the feed tray and the film web lying on the tray, and gently push into the nip area of the heat rollers (Figure 10). 16. Lower safety shield then push the RUN button. Watch the leading edge of the threading card to ensure that it enters the nip area of the heat rollers and is being pulled into the laminator. The card will guide the web of both film rolls into the heat rollers. Push the STOP button once the threading card has exited the rear of the laminator. 17. Check film alignment. See section entitled FILM ALIGNMENT PROCEDURE for instructions if installed film needs alignment. A CAUTION THE FOLLOWING PROCEDURE IS PERFORMED WHILE THE LAMINATOR IS HOT. USE EXTREME CAUTION. AVOID CONTACT WITH THE HEAT ROLLERS. Method For Tacking New Rim to Existing Film The following describes a method for loading film whereby the existing film present on the heat rollers may be used in place of the threading card to draw the new film through the laminator. The adhesive of the existing film must be tacky or liquefied. Leading edges of the new film will be overlapped onto the tacky adhesive of the old film. The existing film and the new film will be pulled through the laminator together. 1. Preheat the laminator. Remove the feed tray. 2. Cut remaining top and bottom film webs between the supply rolls and heat rollers. 3. Raise safety shield to full upright position. 4. Do not allow the adhesive side of the film to contact the heat or pull rollers. Liquefied or tacky adhesive deposited on heat rollers will require the rollers to be cleaned per the section entitled CARING FOR THE GBC EAGLE SERIES LAMINATOR. 5. Remove bottom film supply roll from laminator and lower bottom film guide. 6. To load new film on film supply shafts repeat steps 9 and 10 in subsection Method Using Rim Threading Card. 7. Unroll enough film from the bottom roll of film to slide under the bottom idler bar and tack to the existing film. Slide the bottom idler bar back into place and replace supply roll shaft. 8. Replace the top supply roll shaft and unroll enough film to tack to the existing top roll of film. 9. Install feed table and lower safety shield. 10. Press SLOW button for slowest speed setting and press the RUN button. 11. Observe the film being pulled through the laminator to assure that the remaining existing film and the new film are advancing concurrently. Any separation between the films will require stopping the motor immediately and the situation corrected. 12. Press the STOP button once the newly threaded film is completely exiting the laminator. MOUNTING Tips For Threading Pressure Sensitive Film 1. Use kraft paper whenever the items to be laminated are narrower than the film you are using or you can not consistently feed the items without a gap. 2. Thread the film c...
Este manual também é adequado para os modelos :Laminador - 105 (3.39 mb)