Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
The DocuBind TL300 punches up to 12 sheets of 20 lb./80 gram paper at once. Punch only TWO clear covers at a time to prevent jams and excessive wear. 5. If punch jams, depress the RESET[2]button (D3). Then press the PUNCHES button (D2) again and remove paper or covers from punch throat (it may be necessary to punch several times in order to remove the paper). Repeat steps 1 to 4 with slightly less paper to avoid punch jams on additional lifts. Thank you lor purchasing the GBC DocuBind TL300. This system features our new exclusive wire holder design that enables you to assemble your document as you punch, making it easier to load paper onto the binding comb than previous systems! The DocuBind TL300 advanced punching technology also makes it easier to punch more paper at once while providing greater reliability. A. GETTING STARTED 1. Push the handle (A) onto the shaft located on the right side of the machine (see figure 1). Align the flat spot of the handle with the flat of the shaft and secure It with the alien wrench provided. 2. Insert U shaped wire support bracket into holes on top rear of machine. 3. Firmly push the female end of the power cord into the power cord receptacle (A1) located on the back of the machine. A CAUTION: Make sure this step is complete prior to plugging the male end of the power cord into a power receptacle. 4. Plug the male end of the power cord into an appropriate power receptacle. B. DETERMINE SHEET WIDTH 1. Set Edge Guide (B) to paper size you wish to bind (11”, 8-1/2” letter size, 11-1/4” oversized cover, A4 ring, A5, Japan A4) (see figure 1). When using oversized covers, set the Edge Guide on Covers, punch all of the covers for your job and set aside. Move the Edge Guide back to the 11 ” setting to punch your contents then bind. C. DETERMINE WIRE SIZE 1. Slide the Binder Sizer open (C) (see figure 1). 2. Place document including covers behind Binder Sizer. 3. Release the Binder Sizer and select the wire binding element that corresponds with the size shown by guide. For best results, always use GBC brand covers with GBC color-coordinated wire. D. PUNCHING PAPER (sea figure 2) 1. Lift the Paper Support (D) into place (optional). 2. Align sheets or covers and insert edge to be bound into punch throat (D1). 3. Jog the sheets until they are flush against the edge guide and the bottom of the punch throat. Allow the paper to rest against the Paper Support, or, you may prefer to hold the sheets in place with one hand. E. BINDING 1. Using the dial on the left side adjust the Wire Crimper to correspond with the wire element size to be used. 2. Place the large loops of the wire element into the Wire Holder as shown in figure 3. Be sure it is firmly secured with the small loops facing toward you. 3. Place your punched pages face downward onto the small loops of the wire element. Then place your front and back covers face-to-face against each other. Place the covers onto the wire element with the back cover first and the inside of the front cover facing upward. This step ensures that after crimping the seam of the wire element will be hidden between the back cover and last page (figure 4). 4. Hold the wire element firmly at each end of the book and remove it from the Wire Holder by sliding it to the left or lifting it off. While firmly holding the wire element at each end place the book with the open end of the wire face down into the Wire Crimper. You can release the book so it rests against the support rack or continue to hold it with one hand (figure 5). 5. To crimp the wire together pull the handle down toward you completely until it goes no further. Remove the book and flip the front cover around to the front. Your presentation is now complete. F. EMPTY CHIP DRAWER 1. Empty Chip Drawer (F) after repeated use. Pull drawer gently toward you to open. When putting back in, the drawer will snap into place (see figure 6). G. SERVICE Should your DocuBind require service contact: Quartet, a GBC Company 5700 Old Orchard Road Skokie, IL 60077 USA 1-800-541-0094 18” (W) x 8 1/2” (H) x 16” (D) 457mm x 216mm x 406mm 115V AC, 60Hz, 4.3 amps, 130 watts or 230V AC, 50Hz, Punch Capacity: Bind Capacity: 12 sheets of 20 lb. paper 12 sheets of 80gm* paper 125 sheets or 9/16" (14mm) Maximum Sheet Width: 11.7” (297mm A4) Dis-engagable Punch Pins: 1 (A5 paper) within wire storage bin SAFETY MESSAGES Your safety as well as the safety of others is important to GBC. In this Operator Manual and on the product are important safety messages. Read these messages carefully. A The safety alert symbol precedes each safety message in this Operator Manual. This symbol indicates a potential personal safety hazard that could hurt you or others, as well as cause product or property damage. The following warning is found on this unit: This safety message means you could be seriously hurt or killed if you open the product and expose yourself to hazard...