Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
The heat shoes can reach temperatures in excess of 300°F. • Keep hands and fingers away from the path of the sharp film cutter blade located at the film exit. • Do not place the laminator on an unstable cart, stand or table. An unstable surface may cause the laminator to fall resulting in serious bodily injury. Avoid quick stops, excessive force and uneven floor surfaces when moving the laminator on a cart or stand. »Do not defeat or remove electrical and mechanical safety equipment such as interlocks, shields and guards. • Do not insert objects unsuitable for lamination. • Do not expose laminator to liquids. Electrical safeguards • This laminator must be connected to a supply voltage corresponding to the electrical rating as indicated on the serial plate located on the rear of the machine. • Unplug the laminator before moving it, or when it is not in use for an extended period of time. »Do not operate the laminator with a damaged power supply cord or plug. • Do not overload electrical outlets as this can result in fire or shock. • Do not alter the attachment plug. This plug is configured for the appropriate electrical supply. The unit is intended for indoor use only. \ CAUTION: The receptacle must be located near the equipment ~ and easily accessible. Do not use an extension cord. Disconnect the attachment plug from the receptacle to which it is connected and keep the power supply cord in your possession while moving the laminator. Do not operate the laminator with a damaged power supply cord or attachment plug, upon occurrence of a malfunction, or after laminator has been damaged. Contact an authorized GBC service for assistance. A Perform only the routine maintenance procedures referred to in these instructions. A Do not attempt to service or repair the laminator. Unplug the unit and contact an authorized GBC service representative for any required repairs If one or more of the following has occurred: • The power supply cord or attachment plug Is damaged. • Liquid has been spilled into the laminator. • The laminator is malfunctioning after being mishandled. • The laminator does not operate as described In these instructions. A WARNING: THIS IS NOT A TOY - DO NOT ALLOW CHILDREN TO OPERATE THIS LAMINATOR! Installation • Shipping damage should be brought to the Immediate attention of the delivering carrier. • Place the laminator on a stable flat surface capable of supporting 110lbs. The surface should be at least 30” high to assure comfortable positioning during operation. All four rubber feet should be on the supporting surface. • Connect power cord to an appropriate power source. Avoid connecting other equipment to the same branch circuit to which the laminator is connected as this may cause nuisance tripping of the circuit breaker or blown fuses. »The laminator should be positioned to allow exiting film to drop freely to the floor. Accumulation of laminate as it exits the laminator may cause film to wrap around the rollers, causing a jammed condition. • Avoid placing laminator near sources of heat or cold. Avoid locating the laminator In the direct path of forced, heated or cooled air. Caring for th e GBC Pinnacle 27- Roll Laminator The only maintenance required by the operator is to periodically clean the heat shoes. The following procedure will help keep the heat shoes free of adhesive that has been deposited along the edge of the laminating film. |\ CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED WHILE THE LAMINATOR IS HOT. USE EXTREME CAUTION. A A A |\ WARNING: Do not apply cleaning fluids or solvents to ~ the rollers. ’I\ WARNING: Do not attempt to laminate adhesives marked ‘Flammable’. O Remove the film from the laminator following the procedure outlined in the section FILM LOADING AND THREADING. Q Preheat the laminator until the READY LAMP (O) illuminates. Q Clean the top and bottom heat shoes with a soft cloth. O Follow the procedure in section FILM LOADING AND THREADING, Method Using Film Threading Card to reload the laminator. NOTE: Do not use metal scouring pads to clean the heat shoesl WARNING: Do not laminate glitter and/or metallic items. Damage to the rollers may result. £> m Roll Laminator GQC Pinnacle 27 Features Guide A. POWER SWITCH: (figure 1) Located at the back of the machine, applies power to the laminator. The ‘ON’ position is indicated by the ‘ I' symbol. The 'OFF’ position marked ‘O' symbol. B. CONTROL PANEL: (figure 2) • POWER LAMP (I): Indicates that the laminator is plugged into the power source, the main power switch is in the 'ON' (I) position and the stand-by switch (cb) is pressed on. • READY LAMP (o): This will illuminate when the laminator has reached operating temperature. • STANDBY SWITCH (ci)): Push to turn laminator on or off when main power switch at the rear of machine is in the 'ON' (I) position. • HIGH TEMP SWITCH) I): Push to select high temperature setting. Lights red when selected Referto Lamination Guid...