Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
For any customer support needs, please choose the « Customer Support » tab on Royal Sovereign International Inc. NB-1900N TABLE OF CONTENTS TOPIC PAGE INTRODUCTION MAJOR PARTS CHARACTERISTICS OF NB-1900N SAFETY PRECAUTIONS SET UP CONTROL PANEL SETTINGS HOT LAMINATING COLD LAMINATING COLOR FOIL LAMINATING MOUNTING BOARD LAMINATING CLEAN ROLLERS AND REMOVE JAMMED FILMS IMPORTANT SAFETY CONCERNS MAINTENANCE ASSEMBLY PARTS TROUBLESHOOTING SPECIFICATIONS 333455 7 8 9 10 11 12 12 12 12 13 NB-1900N INTRODUCTION Thank you for purchasing a Royal Sovereign Laminator. To insure high quality lamination, please read this instroduction manual thoroughly. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at (800) 397-1025. MAJOR PARTS Top Cabinet Control Button Panel LEDInput Output Power Cord CHARACTERISTICS LAMINATOR NB-1900N is an advanced laminator of contemporary design, utilizing the lastest in laminating technology. 1. Contemporary design and rounded shape will enhance any decor. 2. A microprocessor is used for added protection. 1) The microprocessor protects the rollers a.Even when power is off, rollers continue to turn until properly cooled down. b.In the event of a power failure, rollers continue turning until properly cooled down. 2) The microprocessor prevents overheating If a temperature sensor fails, the microprocessor prevents rollers from overheating. 3. Designed to prevent heat from radiating through the housing, using powerful fans. 4. Eight function settings, allow you to laminate various types of film. 5. Every time a button is pressed, a buzzor sounds. 6. Temperature is controled automatically for energy efficiency. 3 NB-1900N 4 Failure to comply with any of the following safety procedures could result in serious injury. Keep this information for future reference. 1.To prevent the possibility of fire or injury, do not allow articles of clothing (neckties, scarves, or paperclips etc.) inside the machine. 2. Do not attempt to laminate items that exceed total recommended material thickness. 3.To prevent the possibility of electric shock, do not immerse the laminator in water or permit liquids inside the machine. 4. Do not operate machine for any other purpose other than its intended use.And do not insert sharp objects into front or rear machine openings. 5. This machine is for indoor use only. 6. Do not operate the machine if the outlet or power cord is damaged. And do not alter the electric plug in any way. Contact a qualified electrician. SAFETY PRECAUTIONS 7.The electrical outlet should be installed near the equipment and should be easily accessible. NB-1900N SET UP Place laminator on a sturdy, flat work surface. Allow ample clearence behind laminator for laminated document or photograph to exit completely without bending. Connect laminator to an electrical outlet that matches laminator's rated voltage and power requirements. If an extension cord is required, use a cord rated higher than the laminator's capacity. CONTROL PANEL SETTINGS Eight Functions allow you to laminate as necessary. TACT-BUTTON and LED were designed for your convenience. 1.FUNCTION OF BUTTONS COLD ON/OFF TEMP COLD ON/OFF : Increase setting : Decrease setting : COLD Function : Power On/off 2.DISPLAY COLD NB-1900N B 7 6 5 4 3 2 1 200~Foil 150180~ 80125~Mic 200~250 micron (8~10 mil) film, color foil and mount board laminating 150~180 micron (6~7 mil) film laminating 80~125 micron (3~5 mil) film laminating Cold film laminating 5 NB-1900N 3.INSTRUCTION OF BUTTONS AND LED COLD NB-1900N COLD TEMP ON/OFF B 7 6 5 4 3 2 1 200~Foil 150180~ 80125~Mic 1. Press power button to turn laminator on or off. 2. When you press power button, "FUNC 2" LED is blinking. At this time, function buttons become available. 3. To choose film thickness, press or and you will see the LED read-out. 4. For cold laminating, press then green LED will light up. COLD 5. When you choose any function, a blinking LED light means it's not ready. When the blinking stops, the laminator is ready. 6. When blinking stops, a buzzer will ring once every two minutes. 7. Even if you turn off as soon as finishing laminating, rollers will continue to turn until cooled down properly, and then stop. 6 NB-1900N HOT LAMINATING 1. Press the power button. 2. Choose setting by or 3. When red LED stops blinking and buzzer rings, you're ready to laminate. (It takes 4~5 minutes depending on setting function.) 4. Put document to be laminated, into a laminating pouch. Leave a minimum border of about 3mm(1/8"), to provide a proper edge seal. 5. Insert pouch squarely into opening slot. 6. Finished lamination will exit through rear of machine. 7. Emerging laminated document is hot to the touch. (Always allow lamination to cool down on a flat surface for about a minute before handling, to prevent permanent bending. If document is not laminated well, re-insert it and run it through a second time.) 8. When continuously ...