Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Page 14 3. Turn the Knob (1) and remove the Plastic Cover (2). (See Figure F.) 4. Remove the threephillips Screws (33) located on the left side of the Body (32). (See Figure G.) SCREW (#33) SCREW (#33) SCREW (#33) BODY (#32) FIGURE G FIGURE F KNOB (#1) PLASTIC COVER (#2) 5. Depress the Depth Control Lever (52) and lower the Base (24) so that the Inner Cover (7) and be removed. (See Figure H.) Depth Control Lever (52) hidden from view. INNER COVER (#7) Base (24) FIGURE H SKU 94362 For technical questions, please call 1-800-444-3353. Page 15 6. Depress the Depth Control Lever (52) to hold the Saw Blade (10) in place. Use the Blade Wrench (74) to unscrew and remove the Bolt (8). Release pressure on the Blade Lock Lever. (See Figure I.) 7. Remove the Outer Flange (11). Then, raise and hold the Blade Cover (12) in its “up” position while removing the Saw Blade. (See Figure I.) DEPTH CONTROL LEVER (#52) SAW BLADE (#10) BOLT (#8) OUTER FLANGE (#11) BLADE COVER (#12) SAW BLADE (#10) BOLT (#8) OUTER FLANGE (#11) ARROW POINTING TO FRONT FIGURE I 8. Raise and hold the Blade Cover (12) in its “up” position while installing the new Saw Blade (10). IMPORTANT: When installing the new Saw Blade, make sure the arrow on the Saw Blade points to the front of the Saw. (See Figure I.) 9. Replace the Outer Flange (11) and, while depressing the Depth Control Lever (52), use the Blade Wrench (74) to firmly tighten the Bolt (8) in place. (See Figure I.) 10. Replace the Inner Cover (7). Then replace the Plastic Cover (2), making sure to turn the Knob (1) to lock the Plastic Cover in place. (See Figures G, and H.) 11. Replace the threephillips Screws (33) on the left side of the Body (32). (See Figure F.) SKU 94362 For technical questions, please call 1-800-444-3353. Page 16 Proper Operation During The Cutting Process: WARNING! Never pass hands and fingers directly in front of, to the rear, or below,the Saw Blade (10) when cutting a workpiece. Always push the Saw into the workpiece with both hands firmly gripping the Handles (64, 65, 72). 1. Make all necessary adjustments to the Saw (width and depth) as previously discussed in this manual. 2. Make sure the workpiece is free from screws, rivets, and any other foreign objects which could damage the Saw Blade (10). 3. Make sure the workpiece is supported at all times. Whenever possible, secure the workpiece in a vise or with clamps (not included). If necessary, use a roller stand (not included) with larger workpieces. 4. Before trying new or complicated cutting techniques, study the procedure and practice with scrap metal. 5. Plug the Power Cord (71) into the nearest 120 volt, grounded, electrical outlet. 6. Firmly grip the Handles (64, 65, 72) of the Saw with both hands. Depress the Safety Lock Button (63), and squeeze the Trigger Switch (66) to turn on the Saw. 7. Allow the Saw Blade (10) to spin up to full speed before feeding the Saw Blade into the workpiece. 8. Make straight cuts only. Do not attempt to twist the Saw to the right or left while cutting. If this occurs, the Saw Blade (10) will “bind” in the workpiece causing kickback, potential personal injury, and/or damage to the workpiece and Saw. 9. Do not force the Saw to remove material faster than it was designed to cut. Make sure to feed the Saw Blade (10) gradually into the workpiece. 10. Turn off the Saw if the Saw Blade (10) is to be backed out of an uncompleted cut. When turning off the Saw, allow the Saw Blade to fully stop on its own before removing the Saw. Do not press against the Saw Blade to stop it. 11. Once the cutting job is completed, turn off the Saw and wait until the Saw Blade (10) has stopped rotating. Then, unplug the Power Cord (71) from its electrical outlet. SKU 94362 For technical questions, please call 1-800-444-3353. Page 17 INSPECTION AND MAINTENANCE 1. WARNING! Always unplug the Saw from its electrical outlet before performing any inspection, maintenance, or cleaning. 2. Before each use: Inspect the general condition of the Saw. Check for misalignment or binding of moving parts, loose, cracked or broken parts, damaged wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Daily: The Saw Blade (10) must be sharp and clean to perform properly. Depending on materials cut and frequency of tool use, the Saw Blade may become clogged with metal particles and dull. Dull Saw Blades rub the workpiece rather than cut, which results in increased friction, higher temperatures, and a burned workpiece. As often as possible, check the condition of the Saw Blade and, if necessary, replace a worn Saw Blade with a new, 7-1/4” diameter, metal cutting Saw Blade rated at 5,800 RPM or above. (See “To Install A Saw Blade” section for further information.) 4. DAILY: With a vacuum or compressed air, remove all metal debris from the metal debris compartment of the Saw. To do so, lift up and open t...